3gb05200a.fm5 Page 2 Friday, December 7, 2001 12:29 PM
CONSUMPTION DATA
Terminate the ?Rinse Hold? option:The indicator lamps show the sequence reached in
? Press the ?Rinse Hold? button again; the the programme. After starting the programme, the
Temperature SelectorLoadWaterEnergyApprox. Programme
programme will terminate automatically with sequence indication runs from left to right through
ProgrammeDurationthe final spin cycle for the present wash
Wash, Rinse, Spin.
(°C)(kg)(l)(kWh)(hours : minutes)*programme.
? If you do not wish to spin the clothes, turn the When the sequence of the programme is finished
White Cotton956.054**1.902:00
programme selector knob to the ?Drain? the corresponding lamp goes out.
Coloured cotton606.0491.142:20programme and press the ?Start/Pause?
Coloured cotton405.0440.602:05button again when flashing.DOOR LOCK
?Easy Ironing? button
Synthetics602.5550.801:30The door can be opened when the ?Door Open?
? Can be used together with Cotton and
Synthetics402.5550.601:20Synthetics programmes to make ironing easier.indication is on.
Rapid Plus303.0370.400:30? Increases the water quantity and the clothes
are spun very soft.PROGRAMME END
Delicates301.5600.500:45?Spin Speed Reduction? button
? The remaining time is on ?0:00? and all the
Wool401.0600.450:40? Every programme has an automatic predefined lights of the programme sequence indication
maximum spin speed.
Handwash301.0450.300:40are off.
? Press the button to set another spin speed.
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized ? If the spin speed ?0? is selected, the final 1. Turn the programme selector to the ??
conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in spinning is cancelled but intermediate spin position.
the table in relation to the water supply pressure and temperature, the load and the type of wash.peaks remain during rinse. The water is drained 2. Turn the water supply tap off.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the out only.3. Open the door and unload the machine.
household conditions applicable at that time.4. Close the tap and leave the door ajar to allow
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains START DELAY
the drum to dry out.
the water out.
The ?Start Delay? allows to run the machine at the
CHANGE THE PROGRAMME, TEMPERATURE,
consumer?s convenience, for example at night
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE ?Eco Wash? buttonOPTIONS AFTER PROGRAMME START
PROGRAMME? The duration of the wash is extended and the when electricity is cheaper.
temperature reduced to save up to 40% of energy ? Select programme, temperature and options.1. Press the ?Start/Pause? button to pause the
Add the detergents as described in the programme but maintaining good washing results.? Press the ?Start Delay? button to select the
programme. The light flashes.
table or in the chapter ?Detergents and Additives? in ?Prewash? buttondelay time by 1 to 23 hours;
the booklet.? Only for heavily soiled loads (for example sand, ? Press the ?Start/Pause? button. 2. Select the new programme (with temperature), any
granular dirt) sensible. The cycle time increases ? The time delay indication disappears when the options and another spin speed if you want.
1. Turn the programme selector knob to the programme starts and it is replaced by the 3. Press the ?Start/Pause? button again. The
approximately 15 min.
desired programme.remaining time.new programme continues at the same position
?Intensive Rinse? button
2. The remaining time display shows the duration of ? More water and a longer time in rinse cycle is ? The number of hours preselected can later be where the previous programme was
the chosen programme (in hours and minutes) added.reduced pressing again the ?Start Delay? interrupted. Do not add detergent for this
and the pilot lamp of the ?Start/Pause? button ? This option is particularly suitable for areas with button.programme.
is flashing.very soft water, washing baby linen and helps To cancel the ?Start Delay?.
3. The programme sequence and the predefined people with allergies.? Turn the programme selector to the ? ? CANCEL A PROGRAMME BEFORE THE END
spin speed indication corresponding to the ?Rinse Hold? buttonposition.
? Reselect the desired programme and options
selected programme lights up.? The laundry remains in the last rinse water 1. Press the ?Start/Pause? button to pause the
and press the ?Start/Pause? button.
The recommended temperature (see the indicator) without progressing to the final spin cycle to programme. The light flashes.
avoid creasing and prevent colours from
can be altered by pressing ?+? or ?-? button.2. Set the programme selector to ?Drain?. The
changing.spin indicators show PROGRAMME START?0? and the remaining
? This option is particularly recommended for the time shows ?0:02?.
SELECT ANY DESIRED OPTIONOpen the tap and press the ?Start/Pause? button.
programme ?Synthetics? or ?Delicates?.
The pilot lamp of the ?Start/Pause? button lights up. 3. Press the ?Start/Pause? button to start the
Selecting any option the indication lights up.? This function is particularly useful if you want to drain programme.
When the combination of programme, additional postpone spinning to a later time, or if you want
options and temperature is not possible, the to drain only.
indication lights switch off automatically. Note: The programme stops to ?Rinse Hold? at the
Unsuitable combinations of options are time the ?Rinse Hold? light in the programme flow
deselected automatically.indication is on.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 05200/A
Black Process Plate |
ACEC
