1 - 5
INSTRUCTION FOR USE
CD PLAYFEATURES
Playing a CDSelecting a track and searching
This CD-player can play all kinds of Audio Discs suchSelecting a track during playback
as CD-Recordables and CD-Rewritables. Do not try to" Briey press §or § once or several times to skip to
play a CD-ROM, CDi, VCD, DVD, MP3-CD or computerthe current, previous or next track.
CD.yPlayback continues with the selected track, and
the tracks number is displayed.
1 Push the OPEN 2 slider to open the player.Selecting a track when playback is stopped
1 Briey press §or § once or several times to select
2 Insert an audio CD, printed side up, by pressing thethe desired track. The track number is displayed.
CD onto the hub.
2 Press 2; to start CD play.
3 Close the player by pressing the lid down.yPlayback starts with the selected track.
4 Press 2; to switch the player on and start playback.Searching for a passage during playback
yThe current track number and elapsed playing1 Keep §or § pressed to nd a particular passage in
time are displayed.a backward or forward direction.
ySearching starts while playback continues at low
"You can pause playback by pressing 2;.volume. After 2 seconds the search speeds up.
yThe time at which playback was paused starts
ashing.2 Release the button when you reach the desired passage.
yPlayback continues from this position.
"You can continue playback by pressing 2; again.
Notes: If the player is in SCAN mode (see MODE chapter), searching is not
5 Press 9 to stop playback.possible.
yThe total number of tracks and the total playing
time of the CD are displayed.
6 Press 9 again to switch the player off.
"To remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.
Playback informationProgramming track numbers
Y If a CD-Recordable (CD-R) or a CD-Rewritable (CD-You can store up to 30 tracks to play in a program.
RW) is not recorded properly, NF dISC isA single track may be stored more than once in the
displayed, indicating that the CD has not been program.
nalized. In that case, use FINALIZE on your CD
recorder to complete the recording.1 While playback is stopped, select a track with
Y When playing a CD-Rewritable (CD-RW), please note §or §.
that it takes 315 seconds after pressing 2; for
2 Press PROG to store the track.
sound reproduction to start.
yprogram lights up; the track number
Y Playback will stop if you open the CD lid.programmed and P with the total number of
stored tracks are displayed.
Y While the CD is read, 1 -:- ashes in the display.program
3 Select and store all desired tracks in this way.
Volume and bass
4 Press 2; to start playback of your selected tracks.
Volume adjustmentyprogram is shown and playback starts.
"Adjust the volume by using VOL Å /+ on the CD player
or the slider on your remote control.
"You can review the program by pressing PROG for
more than 2 seconds.The display shows all the storedprogram
tracks in sequence.
Bass adjustmenty Display NO Prog if no tracks programmed.
vol
"Press DBB to switch the bass enhancement on or
Notes: If you press PROG and there is no track selected or no tracks pro-off
grammed, SEL or NO PRogis displayed.
If you try to store more than 30 tracks, FULL is displayed.yis shown if the bass enhancement is
activated.
Clearing the program
"While playback is stopped, press 9 to clear
program.program
y CLRis displayed once, program goes off,
and the program is cleared.
Note: The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically. |
ACEC
