CD-K7000W/C7000W,CP-C7000
OPERATION MANUAL
The 24-hour display will appear. The 12-hour display will appear. The 12-hour display will appear.
???
Press the ON/STAND-BY button to enter the stand-by mode.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to select the time display mode."0:00" (0:00 - 23:59) "AM 0:00" (AM 0:00 - PM 11:59) "AM 12:00" (AM 12:00 - PM 11:59)Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the hour.Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the minutes.Press the MEMORY/SET button.The time display will appear for about 5 seconds.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Perform steps 6 - 9 above.Perform steps 1 - 2 in the section "RESETTING THE MICRO- COMPUTER".Perform steps 1 - 9 above.
Note that this can only be set when the unit is first installed or it has been reset.Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously.When the 12-hour display is selected, "AM" will change auto- matically to "PM".Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. Hold it down to change the time in 5 minute intervals.The hour setting will not advance even if minutes advance from "59" to "00".The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time.
In this example, the clock is set for the 24-hour (0:00) system.123456789To see the time display:Press the CLOCK button.Note:To change the clock time:123To change the time display mode:12
AM 12:00
AM 0:00
MEMORY/SET
0:00
CLOCK
TUNING/ TIME ( )23456789
SETTING THE CLOCK(Main unit operation)ON/ STAND-BY
AM/FM interval (span)Press the ON/STAND-BY button to enter the stand-by mode.Set the SPAN SELECTOR switch to "50/9" for 9 kHz AM interval (50 kHz FM interval), and "100/10" for 10 kHz AM interval (100 kHz FM interval).Whilst pressing down the button and the X-BASS/DEMO button, hold down the ON/STAND-BY button for at least 1 second."CLEAR AL" will appear.The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.Remote controlReplace the batteries if the operating distance is reduced or if the operation becomes erratic.Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth.Exposing the sensor on the main unit to strong light may in- terfere with operation. Change the lighting or the direction of the unit.Keep the remote control away from moisture, excessive heat, shock, and vibrations.To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets).If the display is not correct.If the operation is not correct.Press the ON/STAND-BY button to enter the stand-by mode.Whilst pressing down the button and the X-BASS/DEMO button, hold down the ON/STAND-BY button for at least 1 second."CLEAR AL" will appear.The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.
The International Telecommunication Union (ITU) has established that member countries should maintain either a 10 kHz or a 9 kHz interval between broadcasting frequencies of any AM station. The illustration shows the 9 kHz interval zones (regions 1 and 3), and the 10 kHz interval zone (region 2). Before using the unit, set the SPAN SELECTOR switch (on the rear panel) to AM tuning interval (span) of your area.To change the tuning zone:123Caution:Notes concerning use:Reset the microcomputer under the following conditions:12Caution:
X-BASS/ DEMO
15
15
0.2 m - 6 m (8" - 20')
PREPARATION FOR USERESETTING THE MICROCOMPUTER ON/ STAND-BY
� 8 � |
ACEC
