1-4. Function of Swiches on PC Board
1-4. Function of Swiches on PC Board. S4 (MODE)
Factory-setting: 0
AT-89A board. S4-0 (NORMAL)
Factory-setting position
. S3-1 (625/525 SELECTION). S4-1 (CRT UP/DOWN)
Used to enable selecting the mode of the CHARACTERThe page displayed on the monitor through the CHAR-
output signal when the video signal is not input to theACTER terminal can be changed by switch S5 (UP/
REFERENCE terminal. When the switch is set to ON,DOWN).
the output signal becomes 625 line. When the switch is
set to OFF (to figure side), the output signal becomesThe contents of each page are shown below.
525 line.
PageContents of display
Factory-setting: OFF (for UC)
0No display
ON (for CE)
1No display (when the power is turned on)
When using a camera with the automatic setup
. S3-2 (Not used)function, or it any fault has been detected during self
Factory-setting: OFFdiagnosis, the corresponding details are displayed.
2The connection states of cameras 1 to 6 are displayed.
. S3-3
3The connection states of cameras 7 to 12 are
When this switch is set to ON, OALL� function of thedisplayed (when the BKP-7930 is being used).
MSU will be applied to the camera for which ACTIVE is4The connection states of cameras 1 to 12 are
indicated on the MSU.displayed (when the BKP-7930 is being used).
If this switch is set to OFF, OALL� function of the MSU5The results of automatic setup for cameras 1 to 6 are
will be applied to all cameras connected to the CNU-700displayed.
at the same time.6The results of automatic setup for cameras 7 to 12 are
Factory-setting: OFFdisplayed (when the BKP-7930 is being used).
7The results of all-camera diagnosis for cameras 1 to 6
are displayed.
. S3-4 to S3-7 (Not used)
8The results of all-camera diagnosis for cameras 7 to 12
Factory-setting: All OFF
are displayed (when the BKP-7930 is being used).
9DIAGNOSIS OF ONE MACHINE
. S3-8 (TEST MODE ON/OFF)(The state of the selected device is displayed.)
All setting data of the unit can be initialized by means of10DATA OF ALL CAMERAS
the following procedures.(The settings for all connected cameras are displayed.)
n
11DATA OF ONE CAMERA
Since the setting data such as RCP ASSIGNMENT, etc.(The settings for the selected camera are displayed.)
will be initialized, special care should be taken when
executing this test.. S4-2 (RCP ASSIGNMENT)
Factory-setting: OFFThe connecting condition between the RCP-700 series
1. Turn off the power of CNU-700.and CCU-700 series can be changed.
2. Set S3-8 to on. Set S3-1 through S3-7 to OFF.Operate the switches S5 (UP/DOWN) and S6 (SET/
3. Set the MODE switch S4 to OF.�CANCEL) in accordance with the monitor screen.
4. Set the UP/DOWN switch S5 to ODOWN� and SET/
CANCEL switch S6 to OSET,� namely, take the two. S4-3
switches S5 and S6 with your fingers.Not used.
5. In the state of step 4, turn on the power of CNU-700
and maintains about ten seconds.. S4-4 (DEFAULT RCP ASSIGNMENT)
6. Turn off the power of CNU-700 and reset allUse this switch when resetting the connecting condition
switches to their original positions.between RCP-700 series and CCU-700 series.
Operate the switches S5 (UP/DOWN) and S6 (SET/
CANCEL) in accordance with the monitor screen.
CNU-7001-7 (E) |
ACEC
