1-26
[C4] Setting the Channel Selection Method, Power-Up Conditions
and Decoder (SET UP 4) N SYSTEM CONFIGURATION Menu
OverviewSetting Lists of the SYSTEM CONFIGURATION Menu
The SYSTEM CONFIGURATION menu is used forYResidual subcarrier detection (RESIDUAL SCThis section explains the setting lists displayed in theDEFAULT CH: Select the power-up input channel
the following settings:SW menu) (when using the BKM-24N/25P)menu.(LAST or CH xx).
It is possible to detect residual subcarrier signals fromLAST: Set the channel to the channel that was
Y Channel number entry method (INPUT SELECTphase change by setting the decoder adpatorOsHow to read the setting listsselected at the time the power was last turned
Chapter 2 Menumenu)residual subcarrier switch on.YFor purposes of explanation, each setting list isoff.Chapter 2 Menu
This menu sets the way in which the numeric keypadYAuto color control (ACC SW menu) (when usingpreceded by a menu number. These numbers are notCH xx: Set the channel to a specific channel
can be used to enter channel numbers.the BKM-27T)displayed on the screen.number.
YPower-up condition (STANDBY MODE menu)Selects if the ACC (Auto Color Control) circuit isFor more information about the menu number, see OAboutDEGAUSS DELAY: Set the time between power-up
This menu sets the condition of the monitor when theactivated or deactivated.menu numbers� on page 23.and the beginning of degaussing. Enter the desired
MAIN POWER switch on the rear panel is switchedYSetting of the contrast and brightness afterYThe arrow mark (�) refers you to another setting listtime (in seconds).
on.adjusting the white balance (CONT/BRT HOLDthat appears after you make the setting, or to anRESIDUAL SC SW: Set the residual switch (OFF or
YPower-up input channel (DEFAULT CH menu)menu)operation that is carried out as a result of the setting.ON).
This menu sets the power-up input channel.Selects if the adjusted contrast and brightness areWhen there is no arrow mark, the menu does not haveACC SW: Set the ACC switch (OFF or ON).
YTime from power-up until degauss (DEGAUSSretained or they are reset to the center values.any sub-list.CONT/BRT HOLD: Select the contrast and
DELAY menu)YAssigning shortcut to the COLOR TEMP ADJbrightness settings to the center or adjusted value
If several monitors are turned on at the same time andmenu to the [F2] key (COL TEMP SHORT-CUT[C4] SYSTEM CONFIGURATION menuafter adjusting the white balance or auto
Set each of the following items.
all start degaussing at the same time, there will be amenu)adjustment of CONTROL PRESET ADJ (OFF or
INPUT SELECT: Select the channel number
very large current draw on the power supply for a fewAssigns the shortcut to the MANUAL menu of theON).
moments. To prevent this, the delay time betweenCOLOR TEMP ADJ menu to the [F2] key. Thisselection method (DIRECT or 10KEY).ON : The contrast and brightness are set to the
power-up and degaussing can be set for each monitorallows you to jump directly to the MANUAL menu(In the explanation below, x and y represent anyvalue before adjusting.
independently.corresponding to the color temperature set to thedigit between 0 and 9.)OFF: The contrast and brightness are set to the
DIRECT mode: When selecting a number from 1
currently displayed image (STD/COL 1/COL 2/CHcenter value (1000) after adjusting.
to 9, press the x button to display channel x.
SET).COL TEMP SHORT-CUT: Assign the shortcut
When selecting a number from 10 to 99, pressfunction to the MANUAL menu of the COLOR
the 0, x, and y buttons to display channel xy (aTEMP ADJ menu to [F2] key (OFF or ON).
two-digit channel number). This mode isON : Assigns the shortcut to the MANUAL menu
Structure of the SYSTEM CONFIGURATION Menuselected at the shipping.of the COLOR TEMP ADJ menu.
10KEY mode: When the x button is pressed
OFF: Does not assign the shortcut to the
followed by the ENTER or Ent button, theMANUAL menu of the COLOR TEMP ADJ
Level 1Level 2monitor displays channel x. When the x buttonsmenu.
is pressed, followed by the y and ENTER (Ent)
INPUT CONFIGURATION C1buttons, the monitor displays channel xy (a two-
BVM-D20F1A/D20F1E/D20F1U/D24E1WA/D24E1WE/D24E1WUREMOTE C2digit channel number).
PASSWORD C3When multiple monitors are connected by a
SYSTEM CONFIGURATION C4INPUT SELECTserial remote connection, this setting will be
ON SCREEN SET C5 STANDBY MODEcommon to all the monitors. It is not possible to
ALIGNMENT C6DEFAULT CH
WHITE UNIFORMITY C7DEGAUSS DELAYchange the setting for individual monitors.
EXTEND MENU C8RESIDUAL SC SWSTANDBY MODE: Select the power-up condition
ACC SWwhen the MAIN POWER switch is turned on (OFF
CONT/BRT HOLD or ON).
COL TEMP SHORT-CUTON : Standby mode
OFF: Operation mode
4445 |
ACEC
