LOADING AGING MODETABLE ROTATION MODE
Y This mode is used for repeating loading operations continuouslyY This mode is used for electrical adjustments. Refer to the sec-.
Y Aging will be performed continuously unless an error occurs.tion on Electrical Adjustments.
Y When an error occurs, the error code will be displayed on the
fluorescent indicator tube.TITLE MEMO SHIFT MODE
Y This mode is used for writing title memo information recorded
Procedure:in this unit in a different unit.
1. Set a disc in the DISC 1 slit.Use it for transferring disc memo contents written by the cus-
2. With the power ON, while pr[GROUPE2]essing the buttontomer to the new units when replacing the unit, etc.
and [EEEOPEN/CLOSE]¤ button, press the [+100] button.
3. When the mode is set, both the [EEEEE]á and [EEEE]P indicators willConnection:
start to blink.
Flow of data
4. When the [EEEEE]á button is pressed, only the [EEEEE]á indicator will$
blink and aging starts.
5. To release the mode, press the [EEEEE]1/u button.This unit$$Another unit$
(Copy source)(Copy destination)
The error codes displayed during operations and when errors oc-
cur are the same as the OAGING MODE � described earlier.
COMMAND MODE: CD3COMMAND MODE: CD1
TABLE AGING MODE
Y This mode is used for rotating the table randomly.CONTROL A1 II connection cord
Y Aging will be performed continuously unless an error occurs.provided
Y When an error occurs, the error code will be displayed on theCONTROL A1 II
fluorescent indicator tube.
Procedure:
Procedure:1. Connect two units using the [CONTROLEA1EII] connection cord
1. Set discs in slits 1, 2, 99, 100, and 200.shown in the figure.
2. With the power ON, while pr[GROUPE3]essing the button2. Set the [COMMANDEMODE] switch of the copy source unit
and [EEEOPEN/CLOSE]¤ button, press the [+100] button.to [CD3] and the [COMMANDEMODE] switch of the copy des-
3. When the mode is set, both the [EEEEE] and [EEEE]Pá indicators willtination unit to [CD1].
start to blink.3. With the power on, while pressing the [GROUPE7] button and
4. When the [EEEEE] button is pressed, only the [EEEEE]áá indicator will[EEEOPEN/CLOSE]¤ button of the copy destination unit, press
blink and aging starts.the [+100] button.
5. To release the mode, press the [EEEEE]1/u button.4. When the data has been transferred, the fluorescent indicator
tube displays Ocomplete� for about 1 second.
During aging, operations will be carried out sequentially in the
order of No. 1, No. 2, No. 100, No. 99, and No. 200 slits.MODEL NAME DISPLAY
Y Model names can be displayed on the fluorescent indicator tube
The error codes displayed during operations and when errors oc-for checking the microprocessor model setting, etc.
cur are the same as the OAGING MODE � described earlier.
Procedure:
DOOR POP UP AGING MODEWith the power ON, while pressing the [GROUPE1] and [EEEEE]á
Y This mode is used for performing aging of the CD pop up partbuttons, press the [+100] button.
and door open/close.The model name is displayed on the fluorescent indicator tube.
It is used for checking if operations are performed normally.
MICROPROCESSOR VERSION DISPLAY
Procedure:Y The microprocessor version can be displayed on the fluorescent
1. To select a slot to be a[EEEOPEN/CLOSE]¤ged, press the buttonindicator tube.
and rotate the [DISC/CHARACTER] knob with the front door
opened to select a number.Procedure:
2. With the power ON, while pr[GROUPE4]essing the buttonWith the power ON, while pressing the [GROUPE2] and [EEEEE]á
and [EEEOPEN/CLOSE]¤ button, press the [+100] button.buttons, press the [+100] button.
3. When the [EEEEE]á button is pressed, aging starts, and door open/The microprocessor version is displayed on the fluorescent indi-
close and up/down operations of the pop up parcator tube.t are performed
continuously.
4. To release the mode, press the [EEEEE]1/u button.ALL LIT MODE
Y This mode is used for lighting the whole fluorescent indicator
The number of times aging is performed will be displayed on thetubes and LEDs.
fluorescent indicator tube during operations.
Procedure:
With the power ON, while pr[GROUPE3]essing the and [EEEEE]á
buttons, press the [+100] button.
Both the fluorescent indicator tubes and LEDs will light up com-
pletely.
To release this mode, press the [EEEEE]1/u mode.
14 |
ACEC
