Installation and Connections
Before installing or connecting the unit, please read the
following and pages 3 to 5 of this manual thoroughlyCaution
for proper use.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
WarningThe wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
MAKE THE CORRECT CONNECTIONS.where you purchased this product to have the work done.
Failure to make the proper connections may result in fire or
product damage.USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure to use only the specified accessory parts. Use of other
(Check with your dealer if you are not sure.) Failure to do so maythan designated parts may damage this unit internally or may not
result in fire, etc.securely install the unit in place. This may cause parts to become
BEFORE WIRING, DISCONNECT THE CABLE FROM THEloose resulting in hazards or product failure.
NEGATIVE BATTERY TERMINAL.ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
Failure to do so may result in electric shock or injury due toPINCHED BY A SHARP METAL EDGE.
electrical shorts.Route the cables and wiring away from moving parts (like the
DO NOT SPLICE INTO ELECTRICAL CABLES.seat rails) or sharp or pointed edges. This will prevent crimping
Never cut away cable insulation to supply power to otherand damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wireOs insulation from
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.being cut by the metal edge of the hole.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLINGDO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
HOLES.
When drilling holes in the chassis for installation, takeAvoid installing the unit in locations with high incidence of
precautions so as not to contact, damage or obstruct pipes, fuelmoisture or dust. Moisture or dust that penetrates into this unit
lines, tanks or electrical wiring. Failure to take such precautionsmay result in product failure.
may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE ORPrecautions
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.Y Be sure to disconnect the cable from the (�) battery post before
Bolts or nuts used for the brake or steering systems (or any otherinstalling your CDA-9855R/CDA-9853R. This will reduce any
safety-related system), or tanks should NEVER be used forchance of damage to the unit in case of a short-circuit.
installations or ground connections. Using such parts couldY Be sure to connect the colour coded leads according to the
disable control of the vehicle and cause fire etc.diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle's electrical system.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.Y When making connections to the vehicle's electrical system, be
aware of the factory installed components (e.g. on-board
Swallowing them may result in serious injury.computer). Do not tap into these leads to provide power for
If swallowed, consult a physician immediately.
this unit. When connecting the CDA-9855R/CDA-9853R to
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDERthe fuse box, make sure the fuse for the intended circuit of the
CDA-9855R/CDA-9853R has the appropriate amperage.
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
Failure to do so may result in damage to the unit and/or the
OR GEARSHIFT.vehicle. When in doubt, consult your ALPINE dealer.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.Y The CDA-9855R/CDA-9853R uses female RCA-type jacks for
connection to other units (e.g. amplifier) having RCA
connectors. You may need an adaptor to connect other units. If
so, please contact your authorized ALPINE dealer for
assistance.
Y Be sure to connect the speaker (�) leads to the speaker (�)
terminal. Never connect left and right channel speaker cables
to each other or to the vehicle body.
IMPORTANTSERIAL NUMBER:
Please record the serial number of your unit in the space providedINSTALLATION DATE:
below and keep it as a permanent record. The serial number or theINSTALLATION TECHNICIAN:
engraved serial number is located on the bottom of the unit.PLACE OF PURCHASE:
40-EN |
ACEC
