Troubleshooting Guide
Tips and advice Before starting a wash programme,Cro ckery still dirty after washing:
Arrange crockery so that items do nomake t sure that the spray arms can turn Was the crockery loaded properly?
AFTER-SALES
touch each other. Arrange large freely and are not blocked by crocke Crockery must ry be loaded facing
crockery in the lower rack and smalor culer tlery.downwards; make sure, especially for SERVICE
crockery in the upper rack.Switch off the dishwasher once the large crockery.
Load cups at an angle to facilitate? Start? indicator lamp has switched offTh.e water jets must spray the entire If, after carrying out the above checks the
water drainage.If you switch off the dishwasher dusurfringa ce of all items.malfunction persists or appears again,
Generally speaking, place cutlery ina wash cycl the e, when switched on agai Make sure n that crockery and cutlery are turn the appliance off and turn off the
arranged properly.
basket with the handles positioned the dishwasher resumes the cycle from water supply tap, then call our After-Sales
downwards, but ensure that any sharwp here it was interrupted without havHave you ing selected the correct programme? Service (see guarantee). Please specify:
Did you use too much or too little
knives and forks that might cause to start it. again The nature of the fault.
detergent? (The use of poor quality
injury are placed in the basket with the
detergents result in less effective The appliance type and model.
handles positioned upwards.
washing). The service code (the number after
Make sure the water jet can reach all
Are the filters clogged or incorrectly
loaded items and that the spray arms If a fault occurs, before contacting our the word Service on the
assembled? (See ?Care and
turn freely.After-Sales Service, make the following adhesive rating plate) inside the door on
Maintenance? chapter in the user
Importantchecks to try and remedy the problem:the right-hand side.
instructions).
The dishwasher is not working:
Fill the detergent dispenser and check
Are the spray arms blocked or the nozzles
the salt and rinse aid level. Is the plug properly inserted in the wall
clogged? (See?Ca re and Maintena?nce
socket?
Do not use the appliance for items not
chapter in the user instructions).
Is there a power failure?
suitable for washing in a dishwasher, Is the lower spray arm correctly fitted?
Is the dishwasher switched on?
for example: wooden items, aluminium, Your full address and telephone number.
Is the salt container cap (water softening
Has the Start button been pressed?
plastic utensils, tin, hand-decorated system) screwed down?
Has the delayed start timer been set
crockery (unglazed), silver cutlery.
Marked crockery:
(if fitted)?
Do not put liquid fat in the dishwasher
Is the water hardness level selector not
Is the water supply tap on?
(e.g. oil used for frying) or candle wax.properly adjusted? See?Filli (ng the salt
Is the flow of water obstructed by impurities?
If a fault occurs or you wish to change containe? inr the user instructions).
If so, close the water supply tap, detach the
the current programme, press the Is the salt container empty?
water hose and clean the filter. Then
?START ? button for about 5 seconds (See ?Filling the salt co? intn thainee userr
re-connect the water hose to the tap and
until the Start indicator lamp switches instructions).
open the water tap once again.
off. Was insufficient detergent used?
Are the filters clogged?
If regeneration salt is to be added (See ?Filling the detergent d? inisp enser
(See ?Care and maintenance? chapter in
immediatel starty a wash programme the user instructions).
the user instructions).
in order to eliminate any residual salt Marked glasses and cutlery:
Is the door closed properly?
(rinsing alone is not sufficient). Was too much rinse aid used?
Is a fault indicated?
If a regeneration salt is to be add(Theed, Start indicator lamp flashes).(See ?Filling the rinse aid di? inspe thne ser
IMMEDIATELY start a wash Start the programme again from the user instructions).
programme, in order to eliminate anbey ginning: Press the Start buttonNote: for With some models, when the Start
residual salt (rinsing alone is notab out 5 seconds, until the Start buinttdiocan istor pressed a pre-wash cycle precedes
sufficient).lamp switches off.the actual wash programme; This
Select a new programme and press regeneratthe es the water softening system.
Start button.
Please read the user instructions carefully. |
ACEC
