THERMOMETER FUNCTIONSMOON DATA MODE
A built-in temperature sensor measures temperature and shows the measured valueBe sure to set the current time and your current location before trying to use the Moon
on the display. The thermometer can be calibrated to correct for errors.Data Mode.
The Moon Data Mode display shows the current moon age, as well as moon up and
Importantmoon down times. Moon age is indicated both by a value and one of the following
Temperature measurements are affected by your body temperature (while you aregraphics.
wearing the watch), direct sunlight, and moisture. To achieve a more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe off all moisture from the case. It
takes approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.New Moon CrescentHalf MoonFull MoonHalf Moon
MoonFirst QuarterLast Quarter
Accurate temperature measurements cannot be achieved while you are wearing the
watch. The following graph illustrated affects of body temperature on actualY The moon up time indicates when the moon will
temperature.reach its highest point relative to your current
40°CMoonMoon-UPlocation (upper transit), while the moon down
time indicates when it will reach its lowest point
30°C(lower transit). Note that moon up and moon
Locationdown times are accurate up to ?30 minutes.
20°CEarth
Temperature
Approximate
10°C
Differences caused byMoonMoon-Down
0°Cindividual body
temperture or clothing
10°C20°C30°C 40°CYou can use the key operation below to look up the moon age and the moon up and
moon down times for any date from January 1, 1995 to December 31, 2039.
Temperature measured when watch is worn on wrist
Back
AB
About Temperature Measurement
Temperature measurements are taken automatically every two minutes, regardless ofMoon time date search
what mode the watch is in. You can see the measured values in the Timekeeping
ModeOs Temperature Display. CD
Forward
Understanding the temperature display
1.Use C to enter the Timekeeping Mode.To display the moon up and moon down time for a specific date
Current2.Press D to display the Temperature Display.1.Use C to enter the Moon Data Mode.
temperature *Y Whenever you switch to the TemperatureAY When you enter the Moon Data Mode from
B
ABDisplay, the current temperature is measured andanother mode, the display shows the moon up
displayed.and moon down times for the current date (as
kept in the Timekeeping Mode).
* The display shows O � . � !C� if a measuredCD2.Press D to advance the date or B to move
value falls outside the range of �20!C to 60!C.back. Holding down either button changes the
CDThe normal display will return as soon as theMoon Data Mode Datadate at high speed.
temperature returns within the allowable range.3.When the date you want is displayed, you will
have to wait for about 2 seconds as the watch
Calibrating the Temperature Measurementperforms its internal calculation before displaying
The temperature sensor of this watch is calibrated at the factory before shipment andthe moon up and moon down time for that date.
further adjustment is normally not required. If noticeable error is found in the
temperature readings produced by the watch, you can adjust it to correct the error.
Important
Incorrectly calibrating the temperature measurement of this watch can result inTIDE GRAPH MODE
incorrect readings. Carefully read the following before doing anything.
Y Compare the readings produced by the watch with those of another reliable,Before using the Tide Graph Mode, be sure to first carefully set the current time, your
accurate thermometer.current location, and the lunitidal interval.
Y If calibration is required, remove the watch from your wrist and wait for 20 or 30About the lunitidal interval
minutes to give the temperature of the watch time to stabilize.The lunitidal interval is the period from the moon's upper transit (moon up) to high
Y Perform the temperature calibration before procedure as quickly as possible to avoidtide. If you know the lunitidal interval, tide changes can be determined using the moon
the temperature of the watch being affected by your body temperature.age. This watch calculates tide changes according to the current time and the location
Y You can also preform temperature calibration underwater, if the water temperature issetting, and displays them graphically.
stable.
To calculate the lunitidal interval
To calibrate the temperature1.Look up the high tide time for the flood tide of the location whose tide changes you
1.Use C to enter the Timekeeping Mode andwant to know.
press D to display the Temperature Display.
AB2.Use this watch to look up the moon up time that occurs immediately before this
2.Holding down A and the current temperaturetime.
digits flash.3.Subtracting the moon up time from the high tide time produces the lunitidal interval.
3.Each press of D increase the displayed
temperature by 0.1!C, and pressing the BTo set the lunitidal interval
CDdecrease it by 0.1!C.1.In the Moon Data Mode, hold down A until both
Y You can calibrate the temperature within a rangeABsides of the Tide Graph and hour digits start to
of �9.9!C to +9.9!C.flash, as shown below.
Y Press B and D at the same time to rest theY You can also start this procedure by holding
Flashestemperature calibration to the factory setting.Flashesdown A while in the Tide Graph Mode.
4.After calibrating the temperature, press A to2.Use C to select the digit whose setting you want
CD
return to the Temperature Display.to change. Each press of C moves the flashing
to the next digit.
3.Use D to increase the flashing digit or B to
decrease it. Holding down either button changes
the setting at high speed.
4.After you are finished making the lunitidal setting
you want, press A to enter the Tide Graph
Mode.
N 7 N |
ACEC
