MO0405-EA
Operation Guide 3357
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of yourAbout This Manual
purchase, be sure to read this manual carefully and keep it on hand for later reference? Button operations are indicated using the letters shown
when necessary.Minute handHour handin the illustration.
? Most of the display examples in this manual show only
Expose the watch to bright light to charge its battery before using it.the digital display, without the analog hands.
You can use this watch even as its battery is being charged by exposure to bright? Each section of this manual provides you with the
light.information you need to perform operations in each
? Be sure to read ?Power Supply? for important information you need to knowmode. Further details and technical information can be
when exposing the watch to bright light.found in the ?Reference? section.
If the digital display of the watch is blank...
If the Power Saving on indicator is flashing on the display,Digital display
it means that the Power Saving function has turned off the
display to conserve power. Power Saving automatically
turns off the display and enters a sleep state whenever
the watch is left for a certain period where it is dark.
? The initial factory default setting is Power Saving on.
? The watch will recover from the sleep state if you move it
to a well-lit area,* if you press any button, or if you angle
the watch towards your face for reading.
* It can take up to two seconds for the displa.y to turn on
Digital display? See ?Power Saving? for more information.
Power saving on indicator
General GuideWorld Time ModeAlarm Mode
? Press C to change from mode to mode.
? In any mode, press B to illuminate the face of the watch.NYC
22
? The Battery Level Screen shows the current battery level. See ?Battery Power
Levels? for more information.
Battery Level Screen
Timekeeping Mode
Press C.2
Hand Setting ModeStopwatch Mode
WED
STW
222
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.5. Press A to exit the setting screen.
? In the Timekeeping Mode, press A to cycle through the digital time screens as? When you exit the setting screen, the analog hands are adjusted automatically to
shown below.match the digital time. See ?Analog Timekeeping? for more information.
? See ?Daylight Saving Time (DST)? for details about the DST setting.
? For information about specifying how long the face of the watch remains illuminated,
DateSecondsTime
see ?To specify the illumination duration?.
PM indicator? For details about configuring settings for the Power Saving feature, see ?Power
2 secondsPress A2.2Saving?.
Daylight Saving Time (DST)
Hour : MinutesDaylight Saving Time (summer time) advances the time setting by one hour from
2Standard Time. Remember that not all countries or even local areas use Daylight
Month. DaySaving Time.
Day of week
To toggle the Timekeeping Mode digital time between DST and Standard Time
Setting the Digital Time and Date1.In the Timekeeping Mode, hold down A until the city
This watch is preset with a number of city codes, each of which represents the timecode starts to flash, which indicates the setting screen.
zone where that city is located. When setting the digital time, it is important that you2. Press C once and the DST setting screen appears.
select the correct city code for your Home City (the city where you normally use the3. Press D to toggle between Daylight Saving Time (ON
watch). If your location is not included in the preset city codes, select the preset citylllldisplayed) and Standard Time (llOFF displayed).
code that is in the same time zone as your location.lllllllll4. Press A to exit the setting screen.
? Note that all of the times for the World Time Mode city codes are displayed in? The DST indicator appears on the display to indicate
accordance with the digital time and date settings you configure in the Timekeepingthat Daylight Saving Time is turned on.
Mode.
Analog Timekeeping
To set the digital time and dateThe analog time of this watch is synchronized with the digital time. The analog time
1. In the Timekeeping Mode, hold down A until the citysetting is adjusted automatically whenever you change the digital time.
code starts to flash, which indicates the setting screen.
Note
2.Press D to select the city code you want.
? Make sure you select your Home City code before? The hands for the analog timepiece move to adjust to a new setting whenever any of
lllllllchanging any other setting.lthe following occurs.
lllll? See ?City Code Table? for a complete list of availableWhen you change the digital time setting
lllWhen you change the Home City code and/or DST setting
city codes.
? If the analog time does not match the digital time for some reason, use the
3. Press C to move the flashing in the sequence shown below to select other settings.procedure below to adjust the analog time to the digital time.
? Whenever you need to adjust both the digital and the analog time settings manually,
12/24-Hour make sure you adjust the digital setting first.
City CodeDSTSecondsHourFormat? Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
Power DayMonthYearMinutes
SavingTo adjust the analog time
4. When the setting you want to change is flashing, use D to change it as described1. In the Timekeeping Mode, press C five times to enter
below.the Hand Setting Mode.
? The following steps explain how to configure timekeeping settings only.2. Hold down A until the current digital time starts to
flash, which indicates the analog time setting screen.
ScreenTo do this:Do this:3. Press D to advance the analog time setting by 20
Change the city codePress D (east).lllllseconds.ll
lllll? Holding down D advances the analog time setting at
ll
Toggle between Daylight Saving TimePress D.lllhigh speed.
(ON) and Standard Time (OFF)
? If you need to advance the analog time setting a long way, hold down D until the
Toggle between 12-hour (12H) andPress D.time starts advancing at high speed, and then press B. This locks the high-speed
24-hour (24H) timekeepinghand movement, so you can release the two buttons. High-speed hand movement
Reset the seconds to 00Press D.continues until you press any button. It will also stop automatically after the time
advances 12 hours or if an alarm starts to sound.
4. Press A to exit the setting screen.
Change the hour or minutesPress D(to increase).? The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
Change the year? To return to the Timekeeping Mode, press C.
Change the month or day
1 |
ACEC
