These messages will be received only if Automation (?p.103) 9. Chase Mode[ON, OFF]
is turned off.This is available if OMIDI Sync� is set to OMTC Slave.�
3. Global Ch[01�16]Counter ON:When MTC synchronization begins, playback will Rename
This sets the Global MIDI Channel.chase the MTC messages. After playback begins, if
If you want to use program change messages to transmit two seconds or more elapse without a MTC mes-
METERand receive scene changes, use a MIDI cable to connect sage being received, and there is a discrepancy of
your external MIDI device to the D3200, and set the MIDI two seconds or more between the MTC messages
channel of your connected device to the same MIDI chan-and the current location of the D3200, playback will
MIXER
nel as the D3200Os OGlobal Ch� so that MIDI messages stop and wait for MTC synchronization to resume.
can be transmitted and received.OFF: MTC messages will be chased during playback only
4. MMC Device ID[000�127]when MTC synchronization begins. Once playback CH
VIEW
SpeciŢes the device ID that will be used to transmit and begins, it will continue even if the received time
receive MMC.code no longer matches the internal time code or if
In order to transmit or receive MMC, you must use a time code stops arriving.
EFFECT
MIDI cable to connect the D3200 and the external MIDI
If you are synchronizing with a device other than the D3200
device, set the two devices to the same Device ID, and
as the MTC master, incompatibilities between the devices may
make the appropriate setting in OMMC Mode.�
cause synchronization problems unless you play back from the SEND
If this is set to 127, the D3200 can transmit and receive MMC beginning of the song.
commands to and from units of any device ID setting.
EQ
5. Mode[Transmit, Receive, Off]
This sets the MMC transmission/reception mode.
Transmit: MMC will be transmitted. In this case, the
PAN
MIDI Sync setting will automatically be set to
MTC Slave.
Receive: MMC will be received. In this case, the MIDI
SONG
Sync setting will automatically be set to MTC
Master.
Off:MMC will not be used.
/MIDI/MIDI
SYSTEMSYSTEM
6. Frame Rate
This selects the frame rate that is used when MIDI Sync
is set to OMTC Master� or OMTC Slave.�TRACK
Set this to the same frame rate as used on the external
device with which you are synchronizing.
CD
30: 30 fps (30 frames per second, non-drop)
29NDF: 29.97 fps (29 frames per second, non-drop)
29DF: 29.97 fps (29 frames per second, drop)
25: 25 fps (25 frames per second, non-drop)
24: 24 fps (24 frames per second, non-drop)
7. Time Code Offset
[00:00:00.00F�23:59:59.29F] (for frame rate 30)
ReferenceThis speciŢes an offset value that will be re�ected in the
counter.
The offset value you specify here will be the starting
value for the counter. This will apply when the counter is
set to display frames and MTC/MMC is enabled.UNDO
8. MIDI Sync
[MIDIClockMaster, Off, MTC Master, MTC Slave]
This selects the synchronization mode used when syn-TUNER
chronizing via the MIDI IN/OUT connectors.
MIDIClockMaster: MIDI clock data will be transmitted.
DRUMS
SESSION
Off: Synchronization messages will not be transmitted or
received.
MTC Master: The D3200 will operate as the master de-
STORE SCENE
vice. At this time if the MMC Mode is set
to Transmit, the Chase Mode setting will
automatically be turned Off.MARK
MTC Slave: The D3200 will operate as the slave device.
At this time if the MMC Mode is set to Re-
ceive, the Chase Mode setting will auto-
SCRUB
matically be turned ON.
LOC 1/IN ... LOC 4/END
MODE
REC/PLAY
keys
Transport
125 |