�� Press R (43) or Q (36) on the remote to search forwardRREECCOOVVEERR ....recovery procedure performed automatically after
or backward at twice the playing speed.power failure during recording. If this procedure
fails, the CD-R disc - unlike the CD-RW disc - may
�� Press FAST (45) and then R (43) or Q (36) on the
no longer be usable
Englishremote to search forward or backward at eight times the playing
speed.OOPPCCFFAAIILL ....OPC has failed; disc is damaged or player is defect
�� Press REPEAT (47) to repeat the track that is currently dis-SSEERRVVIICCEE ....recorders self-test has failed; see Fixing problems;
played. REPEAT 1 will appear on the display.
contact your supplier
DIG AUTO TRACK REPEAT 1TOTAL REMTRACK TIMECD SYNC
ANALOGRECORDNNOO AAUUDDIIOO ..no audio information is available on the disc.
FINALIZE
PROGERASE
RECORDABLEL
-50 -40 -30 -20 -10 -6-30OVER
CD REWRITABLERPAUSE
FIXING PROBLEMS
�� Press REPEAT (47) again to repeat the entire disc or pre- pro-
grammed sequence. REPEAT will appear on the display.The numbers between parentheses refer to the fold-out illus-
tration.
2 Press STOP (15 or 34) to stop playing.
If you think your CD Recorder is defective, it is wise to read this list
Programmed playfirst. Maybe you forgot a simple step.
1 With the CD Recorder stopped, press PROGRAM (41) on the
SYMPTOM..........SOLUTION
remote control.
2 Enter the tracks you want to play using the numeric keys (33).No power............" check to ensure that POWER button (1) is on.
For 2-digit track numbers, enter both digits in quick succession." check to ensure that the AC mains cable is
plugged in correctly
�� You can program up to 20 tracks in any order.
" switch the recorder OFF and then immediately
back ON
3 To play your program, press PLAY (13 or 45).
No sound .........." check the audio connections
�� To cancel the program, press STOP (15 or 34) twice, or open
" if using an amplifier, try using a different source
the drawer.
Amplifier sound
is distorted ........" the line outputs on the CD Recorder may not be
connected to the PHONO input; make sure this
ADDITIONAL INFORMATIONis not the case
Play will
not start.............." check to ensure that the label of the CD is fac-
Specific display messagesing up
" clean the disc
MESSAGE ....MEANING" check that the disc is not defect by trying anoth-
er disc
RREEAADDIINNGG ....disc information is being read
Remote control does
OOPPCC................laser power calibration in progress
not work ............" point the remote control directly at the CD
Recorder
NNOO DDIISSCC......no disc present or disc is unreadable
" check the batteries and replace if necessary
UUPPDDAATTEE........the table of contents of the disc is being updated
Will not record .." no recordable disc has been inserted
after a recording
" check the disc and replace if necessary
" use better source or SRC-input mode
WWAAIITT ............the player is performing internal actions
Recording is
FFUULLLL ............the playback program already contains twenty num-
distorted ............" make sure the recording level was not too high
bers; it is full
20 second pause between
CCDD FFUULLLL......there is no room for additional recording
recordings ........" see Automatic recording from a digital source
CD-SYNC p. 10
EEMMPPTTYY ..........the disc contains no recordings; it cannot be final-
Player does
ized
not react ............" use the ON/OFF (1) button on the front of the
IINNPPUUTT ..........no digital input was selected for CD-SYNCplayer to switch it off and back on
FFIINNAALL ........OPC has been performed 96 times (maximum num-
ber of calibrations); the disc must be finalized
12 |
ACEC
