1. Dustcover8. Power switch with15. Tonearm
2. Hingestrobe-lamp16. Armrest
3. Puck9. START/STOP-button17. Tonearm-clamp
4. Platter10. Speed-selector18. Tonarm-lift
5. Center11. Target light19. Anti-Skating-wheel
6. Slipmat12. Lamp switch20. Counterweight-scale
7. Voltage selector13. Headshell21. Counterweight
(underneath the platter)14. Pitchfader22. Cartridge holder
6. CONNECTIONS
BD-1520BD-1520OMNITRONIC
CAUTION!
230/115V AC230/115V ACReadmanualbeforeuse.
Topreventelectricalfireandshockhazard,donotexposethisappliance
~ 50/60Hz~ 50/60Hztomoisture.Riskofelectricshock!Donotopen!DisconnectfrommainsREMOTE
8W8Wbeforechangingfuse.Replacethefuseonlywiththesametypeandrating.
VorGebrauchAnleitunglesen.
GerätvorFeuchtigkeitschützen.BeiSicherungswechselNetzsteckerziehen!
Gefahr!Gerätnichtöffnen!NurSicherungenmitgleichenLeistungswerteneinsetzen.
Lirelemoded?emploiavantl?utilisation.
Afindeprévenirtousrisquesd?électrocutionetdecourt-circuits,nepasexposer
al?humidité.DAttention!Nepasouvrirleboîtier! ébrancheravantde remplacerlefusible.START/STOP
Utiliserunfusiblederechangedememetype.
Connect the RCA-cables (white=left channel, red=right channel) with the PHONO IN-sockets of your
amplifier or mixer. Connect the ground lead with the ground terminal of your amplifier or mixer.
You can connect a footswitch etc. with the REMOTE START/STOP socket.
Connect the turntable to the mains.
7. ADJUSTING
A) Adjusting the counterweight
Remove the stylus cover.
Set the Anti-skating-wheel to the 0 position.
Set the tonearm lift to the down position
Release the tonearm from the armrest and move it to a position between the turntable and the armrest.
Make sure that you do not damage the stylus.
Carefully hold the tonearm and adjust the counterweight by turning it clockwise or anti-clockwise
respectively. The tonearm should be balanced to a horizontal position.
Move the tonearm back to the armrest and clamp it.
Set the scale on the counterweight to the 0 position without turning the counterweight.
Turn the counterweight clockwise until the scale shows the value corresponding to the pressure of the used
stylus. The stylus pressure of the pick-up system included in the delivery is 2.5 g. Should you use a separate
pick-up system, please follow the manufactuer's instructions.
B) Adjusting the tracking force
Set the Anti-skating-wheel to the value equivalent to the pressure of the used stylus. The stylus pressure of
the pick-up system included in the delivery is 2.5 g. Should you use a separate pick-up system, please follow
the manufacturer's instructions.
C) Adjusting the playback-speed
Set the speed to 33 rpm
Press the START/STOP-button and the turntable begins to rotate.
Watch the dotted lines on the platter's edge. The numbers next to the strobe-lamp correspond to the
playback-speed adjusted via the Pitchfader.
Should the dots of the upper line seem to be standing still, the playback-speed is +7,2 %,
should the dots of the second line seem to be standing still, the playback-speed is +3,3 %,
should the dots of the third line seem to be standing still, the playback-speed is 0 %,
should the dots of the lowest line seem to be standing still, the playback-speed is -3,3 %,.
13 |
ACEC
