Important Safety Instructions
17) If an outside antenna is connected to theEXAMPLE OF ANTENNA
televisionequipment, be sure the antenna systemGROUNDING AS PER (NEC)
NATIONAL ELECTRICAL
is grounded so as to provide some protection
CODE
against voltage surges and built up staticANTENNA
charges. In the U.S. Selection 810-21 of theLEAD-IN WIRE
GROUND
National Electrical Code provides information
CLAMP
with respect to proper grounding of the mast and
ANTENNA
supporting structure, grounding of the lead-in wireDISCHARGE UNIT
ELECTRIC (NEC SECTION 810-20)
to an antenna discharge unit, size of grounding
SERVICE
conductors, location of antenna discharge unit,EQUIPMENTGROUNDING CONDUCTORS
connection to grounding electrodes, and (NEC SECTION 810-21)
GROUND CLAMPS
requirements for the grounding electrode.
POWER SERVICE GROUNDING
18) An outside antenna system should not be locatedELECTRODE SYSTEM
in the vicinity of overhead power lines or other(NEC ART 250, PART H)
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an
outside antenna system extreme care should be taken to keep from touching such power lines or circuits
as contact with them might be fatal.
19) Unplug this LCD TV from the wall outlet, and refer servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the LCD TV.
c. If the LCD TV has been exposed to rain or water.
d. If the LCD TV does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to restore
the LCD TV to normal operation.
e. If the LCD TV has been dropped or the cabinet has been damaged.
f. When the LCD TV exhibits a distinct change in performance - this indicates a need for service.
20) When replacement parts are required, be sure the service technician to use replacement parts specified by
the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
21) WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
22) CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG WITH A RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
23) CAUTION: USE WITH OTHER STAND MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
24) CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
NOTE: This equipment is designed to operate in the U.S.A. and other countries where the broadcasting
Y
system and AC house current is exactly the same as in the U.S.A.
The marking or retained image on the LCD panel resulting from fixed image use is not an operating
Y
defect and as such is not covered by Warranty. This product is not designed to display fixed image
patterns for extended periods of time.
Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.
The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel.
This background image is viewable on normal programs in the form of a stationary fixed image. This type of
irreversible LCD panel deterioration can be limited by observing the following steps:
A. Reduce the brightness/contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
This product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of mercury. Disposal of
these materials may be regulated in your community due to environmental considerations. For disposal or recycling
information please contact your local authorities, or the Electronics Industries www .eiae.org.Alliance:
3 |
ACEC
