1@&4@@@@64"�?´
3. Pull up the arm of the self-clean-� The course will startReplacing the Detergent CartridgeIn cases when the status lamp is
ing recharger until it clicks (seeapproximately six secondsReplace the HydraClean� Shaving illuminated, detach the shaver from
fig. 17-3).after being selected.the self-cleaning recharger and carrySystem Solution Cartridge when it
4. Remove the protective cap and* Press the select button withinout the following inspections.has reached the end of its service
� Note that there are cases where the
set the shaver firmly onto the self-six seconds to choose alife. Normally, it is recommended to
blade will be hot or wet if cleaning
cleaning recharger until it clicksdifferent course (see fig. 3).replace it every 30-40 days if used
is not completed.
(see fig. 17-4).
once every day. Use the below chart � Check to ensure that the clean
� Ensure that the outer foil doesWARNING � Do not remove the
as a guide.lamp has been extinguished.
not get deformed or damagedshaver from the self-cleaning
1. Is the water tank and its cap set
during setting.properly?recharger when courses that
Note: In order to maintain maximum
� Before using the self-cleaninginclude the (Dry) function are in? Attach the water tank and its
cleaning performance, it is
recharger, make sure theuse. A heater is used during thecap properly.
important to replace the water
shaver has been rinseddrying process, and this may result2. Is the self-cleaning recharger
in the water tank at the same
thoroughly with water if it hasin the area around the bladetilted?
time you replace the cartridge.? Place the self-cleaning
been washed with hand soapbecoming extremely hot and
or any other detergent, andcausing burns.Shaving CleaningReusabilityrecharger on a horizontal surface.
swish water off properly before1 time/day approx. 30~40 times
The course will be aborted if theWhen an abnormality has beensetting the shaver into the self-
1 time/day1 time/3 days approx. 10~15 timescorrected in accordance with the
power is cut off during cleaning. Incleaning recharger unit.
above two inspections.
The presence of soap or anythis event, it is necessary to perform1 time/1week approx. 4~7 times
� Hold down the select button for
other detergent residue willthe (Clean/Dry/Charge) or (Clean/approximately two seconds to ex-
It is recommended to clean the
contaminate the cleaningDry) course once again from the be-tinguish the status lamp and start
shaver with the self-cleaning
solution in the self-cleaningginning.each course.
recharger after every shave.
recharger unit and could leadChange the cartridges when theIt will take about 3 hours to finish the
to poor cleaning performance.(Clean/Dry/Charge) or (Clean/Dry)status lamp is illuminated. BeforeWhen no abnormality was found af-
5. To clean the shaver, select eithercourse.exchange, make sure to inspect theter the above two inspections.
the (Clean/Dry/Charge) course orThe clean and dry lamp will blinkcartridges with following procedure.� It is time to replace the detergent
cartridge and cleaning liquid inside
the (Clean/Dry) course.after the (Clean/Dry/Charge) or
Checking the status lampthe water tank. (The same cartridge
(Clean/Dry) course is completed.In cases when the status lamp blinks,To dry the shaver after rinsing,
has been used to clean approxi-
� The self-cleaning recharger iscarry out the following inspections.select the (Dry/Charge) course or
mately 30 ~ 40 days worth of beard
mainly designed to clean the1. Is the detergent cartridge setshavings.)the (Dry) course (see fig. 18).
� The (Charge) course will beginblades (outer foil and inner blades).properly?
? Drain the old cleaning liquid in-
immediately when the shaver
Areas that are not soaked into the? Properly set the detergent car-
side the water tank and refill the
is set onto the self-cleaningcleaning liquid or around the sur-tridge (see fig. 15).
tank with water. Additionally,
recharger.2. Was the detergent cartridge de-
face of the liquid are not subject to
replace the old detergent cartridge
� A total of five courses arecleaning.tached during cleaning?
with a new one.
available.? Reset the detergent cartridge.
Carry out brush cleaning or wash� If the status lamp blinks or
The display will alternate
with water to remove beard trim-illuminates again even after the in-
between (Clean/Dry/Charge)After completing inspection and treat-
mings in these areas.spections and treatments above
? (Clean/Dry) ? (Dry/Charge)ment
have been carried out, contact an
? (Dry) ? (Charge) whenever� Properly set the detergent cartridge
authorized service center.
the select button is pressed.to extinguish the status lamp and
start each course.
1213
1213 |
ACEC
