L01_15524 (GB) 1-1_190705 7/19/05 3:55 PM Page 3
Remote control keys
&Screen information / permanent no.#Standby
To display / clear the program number,name (if it Lets you place the TV set on standby.To turn on the
exists),time,audio mode and time remaining for the TV,press P@@,b,0 to 9 (or �).
sleep feature.Press the key for 5 seconds to activate $Teletext keys (p.8),VCR keys (p.11) and list of
permanent display of the number.This key is also radio stations 1 (p.5)
used to exit from the menu.%Sleep
éSurround Sound (only available on certain versions).To select an automatic standby after a preset time
To activate / deactivate the surround sound effect.
(from 0 to 240 minutes).
In stereo,this gives the impression that the &Format
speakers are further apart.For models equipped To enlarge or compress the picture vertically
with Virtual Dolby Surround*,you can experience (Pre-set image
Dolby Surround Pro Logic sound effects.In mono,a
stereo spatial effect is simulated.Used to access a series of stored settings:Rich,
VCR key *Natural,Soft,Multimediaand return to Personal.
Pre-set sound)Teletext (p.8)
Used to access a series of stored settings:Speech,~Program selection
Music,Theatreand return to Personal.To access the next or previous programme.The
(Menunumber, (name) and sound mode are displayed for a
To call up or exit the menus.few moments.
§Cursor / FormatFor some programs,the title of the program will be
These 4 keys are used to navigate through the displayed at the bottom of the screen.
menus.The îI keys are used to enlarge or +Teletext keys (p.8)
compress the picture vertically.or VCR keys *
eVolume,Sound mode(only available on stereo versions)
To adjust the sound level.
!MuteUsed to force programmes in Stereo to Mono or,
for bilingual programs, to choose between Dual I or
To mute or restore the sound.Dual II.For TV sets equipped for Nicam reception,
çNumber keysdepending on the programmes,you can force the
Direct access to the programmes.For a 2 digit program,Stereo Nicamsound to Monoor select between
enter the 2nd digit before the dash disappears.
aSelection of EXT socketNicam Dual I,Nicam Dual IIand Mono.
Press several times to select EXT1,EXT2,S-VHS The Mono indication is red when in forced position.
and AV.* ODolby�and the double-D symbols L are trademarks
?Radio / TV modeof the Dolby Laboratories Licensing Corporation.
To switch the TV set to radio or TV mode (for Manufactured under license of Dolby Laboratories
versions equipped with radio).Licensing Corporation.
* VCR key
The remote control lets you control the main functions of the VCR.
Press and hold down the VCR key located on the side of the remote control,then press one of the keys to access
the VCR functions:b%+HîIE?P@#?cEA09
The remote control is compatible with all VCRs using the RC5 standard.
Safety Information
Y Plug the TV into a 220V � 240V AC,50 Hz supply.
Y Disconnect mains plug when :
� the red light below the TV screen is flashing continuously.
� a bright white line is displayed across the screen.
� there is a lightning storm.
� the set is left unattended for a prolonged period of time.
Y Cleaning the TV screen.Never use abrasive cleaning agents.Use a slight damp chamois leather or soft cloth.
Y No naked flame sources,such as lighted candles,should be placed on top of the TV or in the vicinity.
Y Do not place your TV set under direct sunlight or heat.
Y Do not cover or block the TV as it could lead to overheating.
Y Leave at least 5 cm around each side of TV set to allow for proper ventilation.
Y Avoid placing your set (e.g.near the window) where it is likely to be exposed to rain or water.
Y Battery Usage CAUTION � To prevent battery leakage that may result in bodily injury,property damage,or
damage to the unit:
� Install all batteries correctly,with + and � aligned as marked on the unit.
� Do not mix batteries (old and new or carbon and alkaline,etc.).
� Remove batteries when the unit is not used for a long time.
Useful Tips
Y Do not leave your set on standby mode for a prolonged period of time.Switch off set to allow it to be
demagnetised.A demagnetised set supports good picture quality.
Y Do not shift or move the set around when it is switched on.Uneveness in colour in some parts of the screen may
occur.
Y Never attempt to repair a defective TV yourself.Always consult a skilled service personnel.
3 |
ACEC
