SLEEP (See 6)Helpful hints:
� When battery-powered, the projection lens lights up briefly to help save energy.
About Sleep� To a longer projection time, please use the supplied 7.5V AC adapter to oper
This set has a built-in sleep timer, which enables the radio to be automaticallyate the set.
switched off after a set period of time. There are four sleep time options.
MAINTENANCE & SAFETY
Setting and switching off SLEEP
1 Within 1 second, press ALARM RESET / SLEEP twice until the display showsY If you do not intend to use set for a long time, remove the batteries.
Y Do not expose the set to humidity, rain, sand or excessive heat caused by
SLEEP and SL: 60.
The radio is automatically switched on and tunes to the last station.heating equipment or direct sunlight.
Y To clean your set, use a soft damp cloth or chamois leather. Do not use clean-
2 To select other sleep time options, press ALARM RESET / SLEEP again within 1ing products, which contain benzene, thinner, etc. as these may harm the
second before the display returns to clock time.
The display shows in sequence: SL : 30, SL : 15 and OFF.housing.
3 To cancel sleep, press either:ENVIROMENTAL INFORMATION
� RADIO ON/OFF
� REPEAT ALARM / BRIGHTNESSCONTROL.We have reduced the packaging to its minimum using only paper and cardboard.
� ALARM RESET / SLEEP once or more until SLEEP disappears from the Your set consists of materials which can be recycled if disassembled by a
display. specialized company. Please observe local regulations on the disposal of
packing materials and old equipment.
USING THE PROJECTION
You may have the experience of looking for a clock in the darkness. With this
projection feature, you can conveniently project the clock time onto a surface
e.g. walls ceiling (furniture, glasses not recommended).
1 Press PROJECTION ON/OFF to switch on.
The Projection lens lights up red.
2 Turn the Projection lens wheel (maximum 180 degree left or right) and also the
set, if necessary, to find a suitable projection surface. (See 7)
3 To change the projected time upside down, press REVERSE PROJECTION.
4. To change the projection slightly to a different angle, turn the ROTATE PROJEC-
TION ball (maximum 75 degree left or right.).
5. Press PROJECTION ON/OFF to switch off.
The Projection lens goes out.
TROUBLESHOOTINGThe alarm does not function
� Alarm time/ mode not set
If a fault occurs, first check the points listed below before taking the set for repair.Y See SETTING THE ALARM
If you are unable to remedy a problem by following these hints, consult your dealer or
service centre.� Volume too low for radio
Y Increase the volume
WARNING: Under no circumstances should you try to repair the set yourself, as this
will invalidate the guarantee. Do not open the set as there is a risk of � AL 1 (AL) not tuned to a radio station
electric shock!Y Check if the set is tuned to a radio station before you set AL1 and when you
switch off the radio.
No sound
� Volume not adjustedBlurry projection
Y Adjust the volume � Distance/ angle between the projection surface too large
Y Reduce the distance/ angle.
No display backlight / display malfunction/ radio and alarm do not
function
� Set is in Power Low mode
Y Connect AC/DC adapter or insert fresh batteries
Display error / no reaction to any controls
� Electrostatic discharge
Y Press the RESET hole on the bottom of the set with a ball-pen. Or disconnect
set from AC/DC adaptor and batteries for 5 minutes, then re-plug.
Continuous crackling and hiss noise during MW reception
� Interference from other electrical equipment e.g. TVs, computers, fluorescent
lamps
YMove the clock radio away from electrical equipment
Intermittent crackling sound during FM receptionThis product complies with the radio interference requirements of the
European Union.
� Weak signal
The typeplate and production number are located inside the battery
Y Extend and position the pigtail aerialcompartment. |
ACEC
