safetysŽcuriteseguridad
FEATURESFEATURES / TROUBLESHOOTING
Programming track numbersRESUME and HOLD
You can store up to 30 tracks to play in a program.DBBYou can interrupt playback and continue (even after an
A single track may be stored more than once in the extended period of time) from the position where
program.TRACKplayback stopped (RESUME) and you can lock all buttonsODE
Mof the set so that no action will be executed (HOLD).
1 While playback is stopped, select a track withMODEUse the RESUME�HOLD�OFF slider for these functions.AM
PROGR
or §.
2 Press PROGRAM to store the track.RESUME � continuing from where you have stopped
yprogram lights up; the track number 1 Switch the slider to RESUME during playback to activate RESUME.
programmed and P with the total number ofyresume is shown.
program
Astored tracks are displayed.2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
3 Select and store all desired tracks in this way.
yresume is shown and playback continuesresume
from where you have stopped.
4 Press 2; to start playback of your selected tracks.
yprogram is shown and playback starts.
Y To deactivate RESUME, switch the slider to OFF.
program
yresume goes off.
Y You can review the program by pressing PROGRAM
for more than 2 seconds.HOLD � locking all buttons
yThe display shows all the stored tracks in sequence.You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
Notes: � If you press PROGRAM and there is no track selected, SEL is
transporting the player in a bag. With HOLD activated, you can avoid accidental
displayed.
activation of other functions.
� If you try to store more than 30 tracks, FULL is displayed.
1 Switch the slider to HOLD to activate HOLD.
Clearing the programyAll buttons are locked. HoLd is shown when
Y While playback is stopped, press 9 to clear program.programyou press any button. If the set is switched off,resume
yCLr is displayed once, program goes off,holdwill be shown only when 2;is pressed.hold
and the program is cleared.2 To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to RESUME, you will be acti-
vating the RESUME function.
Note: The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.
Selecting different playing possibilities-MODETroubleshooting
AIt is possible to play tracks in random order, to repeat aWARNING: Under no circumstances should you try to repair the set yourself as
single track or the entire CD, and to play the Ţrst fewDBBthis will invalidate the warranty. If a fault occurs, Ţrst check the points listed,
seconds of each track.before taking the unit for repair. If you are unable to solve a problem by following
1 Press MODE during playback as often as required inTRAODEthese hints, consult your dealer or service center.CK
M
order to activate one of the following �modesO. The
DE
active mode is shown in the display.GRAM MOThe CD player has no power, or playback does not start
PRO
yshuf�e: All tracks of the CD are played in Y Check that your batteries are not dead or empty, that they are inserted
random order until all of them have been played once.correctly, that the contact pins are clean.
yshuf�e repeat all: All tracks of the CDY Your adapter connection may be loose. Connect it securely.
are played repeatedly in random order.YFor in-car use, check that the car ignition is on. Also check playerOs batteries.
yrepeat: The current track is played repeatedly.
The indication no diSC is displayed
yrepeat all: The entire CD is played repeatedly.shufflerepeatall
Y Check that the CD is clean and correctly inserted (label-side upward).
y SCAN: The Ţrst 10 seconds of each of theY If your lens has steamed up, wait a few minutes for this to clear.
remaining tracks are played in sequence.
2 Playback starts in the chosen mode after 2 seconds.The indication nF diSC is displayed
Y CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
Y To return to normal playback, press MODE repeatedly until the display shows
no active modes.
The indicationHOLD is on and/or there is no reaction to controls
Y If HOLD is activated, then deactivate it.
ESP / Power Save Mode
Y Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
With a conventional portable CD-player you might have experienced that the
The CD skips tracks
music stopped e.g. when you were jogging. The Electronic Skip Protection
prevents loss of sound caused by light vibrations and shocks. Continuous playbackY The CD is damaged or dirty. Replace or clean the CD.
is ensured. However ESP does not prevent playback interruptions during vigorousY RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.
running. It also does not protect the unit against any damage caused by dropping!
No sound or bad sound quality.
In this set ESP is default ON. It is possible to set ESP off.
Y PAUSE might be active. Press 2;.and enter the Power Save Mode.(PS). PS helps to extend
battery lifetime for longer playback.Y Loose, wrong or dirty connections. Check and clean connections.
Y Volume might not be appropriately adjusted. Adjust the volume.
Y Press MODE for more than 2 seconds.
ydisappears.Y Strong magnetic Ţelds. Check playerOs position and connections. Also keep
Y Press MODE again for more than 2 seconds.away from active mobile phones.
yPS is displayed once YFor in-car use, check that the cassette adapter is inserted correctly, that the car
cassette playerOs playback direction is correct (press autoreverse to change),
ESP onź ESP offź Power Save ź ESP on
and that the cigarette lighter jack is clean. Allow time for temperature change. |
ACEC
