EnglishControls/Power SupplyPower SupplyGeneral Operation/Tuner
Y Incorrect use of batteries can cause
Supplied AccessoriesBack/bottom panels (See 2General operation
electrolyte leakage and will corrode the
� AC power cord and 3) compartment or cause the batteries to burst:
Switching on and off and selecting the
! Telescopic antenna - improves FM Y Do not mix battery types:e.g.alkaline with car-
function
reception.bon zinc.Only use batteries of the same type
1 To select your sound source, adjust the
Top/front panels (See 1)for the set.@ AC MAINS~ - inlet for power cord.
Source selector to: CD, TUNER or
Y When inserting new batteries,do not try to mix
1 VOLUME � adjusts volume level.# DBB � turns the bass enhancement on/off.OFF.
old batteries with the new ones.
2 Source selector: CD,TUNER, OFF $ p � 3.5 mm stereo headphone socket2 To switch off the set, adjust the Source
Y Remove the batteries if the set is not to be used
� selects CD, or radio source of soundHelpful hints:The speakers will be mutedfor a long time.selector to OFF position and check the
� power off switchwhen headphones are connected to the set.cassette keys are released.
Using AC power
3 Display � shows the CD functions% Battery door - open to insert 6 x 1.5V
WARNING:Always check you have Adjusting volume and sound
4 2; - starts or pauses CD playback completely switched off the set,beforeR-14/ UM-2/ C-cells
Adjust the sound with the VOLUME and
you change or disconnect power supply.
DBB controls.
CAUTION
� selects the next/previous track 1 Check if the power voltage, as shown on
Use of controls or adjustments or
the type plate located on the
� searches forwards/backwards (press andperformance of procedures other
bottom of the set, corresponds to your
than herein may result in unsafehold the button) within the current track
local power supply. If it does not, consult yourRadio reception
REPEAT � repeats a track/operation.dealer or service center.
1 Adjust the Source selector to TUNER.
CD program/entire CD.
2 Connect the power cord to the AC2 Adjust BAND to select your desired
5 PROG � programs tracks and reviews theMAINS~ inlet and the wall socket.The set isThis set complies with the radio
waveband, MW, or FM.
program now connected and ready for use.interference requirements of the
European Union.3 Turn TUNING to tune to a station.
6 LIFT TO OPEN � opens/ closes the CD3 To switch the set off completely, withdraw the
door.power cord from the wall socket.
Helpful hints:
7 TUNING � tunes to radio stations 4 Install the unit near the AC outlet and where
Power Supply the AC power plug can be easily reached.To improve radio reception
8 SHUFFLE � plays all tracks in random order
Whenever convenient, use the power supplyY For FM, extend, incline and turn the telescop-
9 BAND � selects waveband Y Disconnect the power cord from the wall
cord if you want to conserve battery life.socket to protect your set during heavy ic antenna for best reception. Reduce its
Make sure you remove the plug from the setthunderstorms.length if the signal is too strong.0 9 STOP � stops CD playback;;
� erases a CD program
and wall outlet before inserting batteries.
Y For MW, the set uses a built-in antenna.
The type plate is located on the
Direct this antenna for best reception by
Batteries (not included)bottom of the set.
turning the whole set.
1 Open the battery door and insert 6 batteries,
type R-14, UM-2 or C-cells, (preferablyHelpful hints:
alkaline) with the correct polarity as indicated
� To avoid unnecessary energy consumption,
by the "+" and "�" symbols inside the com-
always adjust the Source selector to OFF
partment. (See 2)
after using the set.Also check that the tape
2 Replace the battery door, making sure the bat-deck keys are released.
teries are firmly and correctly in place.The set is
now ready to operate.
Batteries contain chemical substances,so
they should be disposed of properly. |
ACEC
