CD/MP3 PlayerMaintenance & safety (See 9)
2 When you recognize the passage you want,To erase a program
release TUNING / § to resume normalYou can erase a program by:CD player and CD handling Safety information
playback.� pressing 9 (twice during playback or once in
Y If the CD player cannot read CDs correctly,Y Place the set on a flat, hard and stable surface
the stop position);
Helpful hints:� selecting TUNER or OFF position;use a cleaning CD to clean the lens beforeso that the system does not tilt.
� When your searching reaches the end of thetaking the set to repair.Y Do not expose the set, batteries, CDs to
� opening the disc door.
last track,the CD/MP3 goes to stop mode.Y The lens of the CD player should never behumidity, rain, sand or excessive heat caused
� Display: PROG disappears.
touched!by heating equipment or direct sunlight.
Y Sudden changes in the surrounding Y The apparatus shall not be exposed to drip-
Programming track num-
temperature can cause condensation on theping or splashing.
bers Different play modes:
REPEAT and SHUFFLElens of your CD player. Playing a CD is thenY Adequate ventilation with a minimum gap of
You may store up to 20 tracks (for MP3: 10not possible. Do not attempt to clean the
(See 7 8) 15cm (6 inches) between the ventilation
tracks) in the desired sequence. If you like,lens but leave the set in a warm environment
holes and surrounding surfaces is necessary
store any track more than once.You can play the current track or the wholeuntil the moisture evaporates.to prevent heat build-up.
disc repeatedly, and combine REPEAT modes
1 In the stop position, pressTUNING orYAlways close the CD-tape door to avoid dust
§ to select your desired track number.with PROGRAM.on the lens.Y Do not cover the ventilation openings with
items such as newspapers, table-cloths, cur-
REP � plays the current track continuously.
For MP3: First press ALB/PRE +/- once or YTo clean the CD, wipe in a straight line fromtains, etc.
more to find your album.REP ALL � repeats the entire CD/programthe center towards the edge using a soft,Y No objects filled with liquids, such as vases,
2 Press PROG to store the desired trackSHUF � plays all the tracks in random orderlint-free cloth. Do not use cleaning agents asshall be placed on the apparatus.
number.Y Selection of shuffle play is not available in thethey may damage the disc.
Y No naked flame sources, such as lighted can-
� OPROG� is displayed, and display brieflyprogram mode.Y Never write on a CD or attach any stickers
dles, should be placed on the apparatus.
shows current program sequence, thento it.
1 To select play mode, press MODE once orY The mechanical parts of the set contain
the currently stored track number.more.
(see 5 6)self-lubricating bearings and must not be oiled
� The display shows selected play mode.
� OFor MP3: The current album number isor lubricated.
2 Press 2; to start playback if in the stop/pause
also displayed.YTo clean the set, use a dry cloth. Do not use
position.
Y If you attempt to program without first� The disc will play automatically aroundany cleaning agents containing alcohol,
selectig a track, display will show NNOOSSEEbriefly,few seconds later when SHUF mode isammonia, benzene or abrasives as these may
then the total track number.harm the housing.
selected.
3 Repeat steps 1 to 2 to select and store all3 To return to normal playback, press MODE
desired tracks in this way.repeatedly until the modes are no longer dis-
� If you attempt to store more than 20played.
tracks (for MP3: 10 tracks), no track can� You can also press 9 to cancel your play
be stored and the display shows FFuuLLLL.mode.
4 To play your program, press 2;.
To review your program
In the stop position, press PROG to view the
first program information, then press PROG
again to view the next program information.
Repeat the above to view all the program
stored.
� Each time the display shows the program
sequence (PPrrOOgg X) briefly, then the program
track number (see 5 6). |
ACEC
