FM TUNERFM TUNER
Switching radio on/offStoring radio stations
Y Press FM/ once or more to switch the radio on/You can store up to 30 radio stations. Select a preset
number 1-30.
off.
� Display shows briefly Radio on or Radio off1Tune to a desired radio station and press PROG
respectively.briefly.
Use the remote control or set to tune to any FM station 2Press PROGwhile PROGis blinking to confirm the
automatically or manually.storage.
�PROG, the FM frequency and the preset number of
Tuning to radio stations automaticallythe stored station are displayed.
1Press and hold or §for at least 2 seconds.3Store all desired stations this way.
� Display shows briefly Searching.The radio tunes
to a station with sufficient strength and radio play
starts. The FM frequency is displayed.Helpful Hint:
2Repeat searching until you find the desired radio station.Already stored stations can be recognized by a preset
number.
Tuning to radio stations manually
1Keep or §pressed.
2Release or §, then briefly press or §againTuning to a stored radio station
when you are close to the desired frequency.1Press ALBUM +/ -repeatedly if necessary to select
3Briefly press or §repeatedly until you reach thethe preset number of the desired radio station.
desired frequency.� Radio play starts. The FM frequency and the pre-
� Radio play starts. The FM frequency is displayed.set number (P1-30) of the stored station are dis-
YTo switch from radio play to CD play, press 2;.played.
Y Press to switch the radio off.
Helpful Hint:
� To improve reception: The headphone wire is used as an FM antenna.
If necessary, move it for optimum reception.
� Tuner operation is not affected if you open the CD lid to change a disc.
LOCKTROUBLESHOOTING
You can lock the buttons of the set/ remote control respectively by switching theWARNING: Under no circumstances should you try to repair the unit yourself as
slider to LOCK. With LOCK activated, you can avoidthis will invalidate the warranty. If a fault occurs, first check the points listed,
accidental activation of other functions.before taking the unit for repair. If you are unable to solve a problem by following
1Switch the slider toLOCKto activate LOCK.these hints, consult your dealer or service center.
� All buttons are locked. Hold is shown when you
The CD player has no power, or playback does not start
press any button on the set / remote controlYCheck that your batteries are not dead or empty, that they are inserted
respectively. If the set is locked and switched off, Hold will be shown
only when pressed 2; .correctly, that the contact pins are clean.
YYour adapter connection may be loose. Connect it securely.
2To deactivate LOCK, switch the slider to OFForUNLOCK.
The indication Please insert CD is displayed
Y Check that the CD is clean and correctly inserted (label-side upward).
Y If your lens has steamed up, wait a few minutes for this to clear.
The indication Unfinalized CD is displayed
YCD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication Hold is on and/or there is no reaction to controls
Y If LOCK is activated, then deactivate it.
ENVIRONMENTAL INFORMATIONYElectrostatic discharge. Disconnect power or remove batteries for a few seconds.
YAll redundant packing material has been omitted. We have done our utmost toThe CD skips tracks
Y The CD is damaged or dirty. Replace or clean the CD.
make the packaging easily separable into 4 materials: paper, PET, PE and PS.
Y, or PROG is active. Switch off whichever is on.
YYour set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the No sound or bad sound quality.
Y pause might be active. Press 2;.
disposal of packing materials, dead batteries and old equipment.Y Loose, wrong or dirty connections. Check and clean connections.
YVolume might not be appropriately adjusted. Adjust the volume.
Y Strong magnetic fields. Check playerOs position and connections. Also keep
away from active mobile phones. |
ACEC
