ENGLISH
General description (fig. 1).Using the appliance.
A Temperature dial1 Select the required ironing temperature (see section 'Setting the
B Temperature indicatortemperature').
C Mains cord
2 Let the iron heat up for two minutes before you start ironing.
D HeelIf you set the temperature dial to a lower setting after you have ironed at a
E Type plate
F Soleplatehigh temperature, let the iron cool down for five minutes before you
continue ironing.
Important.3 Start ironing when the temperature indicator has first gone out and
Read these instructions for use carefully before using the appliance and savethen goes on again (fig. 3).
them for future reference.BThe temperature indicator will go out from time to time during ironing.
� Check if the voltage indicated on the type plate corresponds to theCleaning and maintenance.
local mains voltage before you connect the appliance.
1 Remove the mains plug from the wall socket and let the iron cool
� If the appliance is provided with an earthed plug, it must be pluggeddown.
into an earthed wall socket.
� Do not use the appliance if the plug, the cord or the appliance itself2 Wipe the soleplate with a damp cloth and a non-abrasive (liquid)
shows visible damage or if the appliance has been dropped.cleaner.
� Check the cord regularly for possible damage.Keep the soleplate smooth: avoid hard contact with metal objects.
� If the mains cord is damaged, it must be replaced by Philips, a service3 Clean the upper part of the appliance with a damp cloth.
centre authorised by Philips or similarly qualified persons in order to
avoid a hazard.Storage.
� Never leave the appliance unattended when it is connected to the
mains.1 Remove the mains plug from the wall socket.
� Never immerse the iron in water2 Wind the mains cord around the cord storage facility (fig. 4).
� Keep the appliance out of the reach of children.
� Young children should be supervised to ensure that they do not play3 Always store the iron standing on its heel in a safe and dry place
(fig. 5).
with the appliance.
� This appliance is not intended for use by young children or infirmEnvironment.
persons without supervision.� Do not throw the appliance away with the normal household waste
� The soleplate of the iron can become extremely hot and may cause
burns if touched.at the end of its life, but hand it in at an official collection point for
recycling. By doing this you will help to preserve the environment
� Do not allow the cord to come into contact with the soleplate when(fig. 6).
it is hot.
� When you have finished ironing, when you clean the appliance andGuarantee & service.
also when you leave the iron even for a short while: put the iron on
its heel and remove the mains plug from the wall socket.If you need information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Customer Care Centre
� Always place and use the iron and the stand, if provided, on a stable,in your country (you will find its phone number in the worldwide guarantee
level and horizontal surface.
leaflet). If there is no Customer Care Centre in your country, turn to your
� This appliance is intended for household use only.local Philips dealer or contact the Service Department of Philips Domestic
Before first use.Appliances and Personal Care BV.
1 Remove any sticker or protective foil from the soleplate and clean itFrequently asked questions.
with a soft cloth.
This chapter summarises the most common problems you could encounter
The iron may give off some smoke when you use it for the first time. Thiswith your iron. If you are unable to solve the problem, please contact the
will cease after a short while.nearest Philips Service Centre or one of its representatives. See the
worldwide guarantee leaflet for telephone numbers of the Philips Helpdesk
Setting the temperature.or visit our website at www.philips.com.
1 Put the iron on its heel.
QuestionAnswer
2 Set the required ironing temperature by turning the temperature dial
to the appropriate position (fig. 2).Why does the soleplate stayThere may be a connection problem. Check the
cold, although I have pluggedmains cord, the plug and the wall socket.
- Check the laundry care label for the required ironing temperature:the iron in?
- 1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)
- 1 SilkThe temperature dial may have been set to MIN.
- 2 WoolSet the required ironing temperature (see section
- 3 Cotton, linen'Setting the temperature').
- If you do not know what kind or kinds of fabric the article is made of,
determine the appropriate ironing temperature by ironing a spot that
will not be visible when you wear or use the article. Start at a relatively
low temperature and gradually increase the temperature until you
obtain the required ironing result.
- Silk, woollen and synthetic materials: iron the reverse side of the fabric
to prevent shiny patches.
- Start ironing the articles that require the lowest ironing temperature,
such as those made of synthetic fibres.
3 Put the mains plug in an earthed wall socket.
4239 000 61001
2/5 |
ACEC
