1-8
Control Panel
3 Effect transition section9 N/R (normal/reverse) button4 Pattern/numeric keypad
To carry out an effect in normal/reverse (i.e.
alternating) mode, press this button, turning it on. It
This is used for effect pattern selection, transition time
2 Display window mode indicatorslights automatically for animation effects and title
setting, and other data entry.
keys.
1 TRANS RATE display window3 SET button
EFFECTq; REV (reverse) button1 PATTERN NUMBER
TRANS RATEDSKdisplay window
FTBSET9 N/R buttonTo carry out an effect in the reverse direction, press
this button, turning it on.PATTERN NUMBER2 SET
button
4 MIX buttonq; REV buttonFor an effect for which normal/reverse (alternating)SET
MIXEFFECTN/RREVoperation is possible, once the effect is carried out, the
5 EFFECT button3 DIRECT RECALL button
Chapter 2 Location and Function ofdirection is automatically reversed. After an effect is4 DIRECTChapter 2 Location and Function of
DIRECTDIRECTPATTERN
RECALLPATTERN
TITLEcarried out in the normal (i.e. forward) direction, thisbutton
button lights. After an effect is carried out in theLAST X
Parts and Controls6 TITLE buttonCUTreverse direction, this button goes off.789INSParts and Controls
qa Fader lever
7 CUT buttonqa Fader lever456DEL5 PATTERN/
qs Fader lever stiffness
adjusting screwP IN PKEY PAD
Move this to carry out an effect transition manually.
8 AUTO TRANS buttonAUTOTRANS123RSTbuttons
qd Transition indicator
Note0DOWNUPENTER
After powering the system on, move the fader lever toPATTERN/KEY PAD
the end of its travel once in each direction. This
ensures that the fader lever will function correctly.
1 PATTERN NUMBER display window
1 TRANS (transition) RATE display window5 EFFECT button
This shows the transition time for effects, downstreamTo carry out the next transition with an effect patternqs Fader lever stiffness adjusting screwThis shows an effect pattern number.
keys, and fade-to-black, in units of frames. While youapplied, press this button, turning it on.Turn this screw with a miniature Phillips screwdriverWhile you are entering a pattern number, the dot at the
lower right of each numeral lights.
are entering a time, the dot at the lower right of eachto adjust the fader lever stiffness. Turn clockwise to
numeral lights.6 TITLE buttonmake the fader lever harder to move, and
To carry out an effect or a mix in title mode, press thiscounterclockwise to make it easier to move.2 SET button
Press this button, turning it on, to enter the pattern
2 Display window mode indicatorsbutton, turning it on. The title keying is carried out,
These indicate the kind of transition time shown in theinserting the characters and graphics with the effectqd Transition indicatornumber specification mode. In this mode, you can use
TRANS RATE display window.pattern and transition settings applied.This indicator consisting of 20 LEDs shows thethe PATTERN/KEY PAD buttons to specify an effect
pattern number.
EFFECT: Transition time of an effectprogress of an effect transition.
Press this button once more, turning it off, to return to
DSK: Transition time of a downstream key7 CUT button
the direct pattern selection mode.
FTB: Transition time of a fade-to-blackPress this button to carry out an instantaneous
transition.
3 SET button3 DIRECT RECALL button
Press this button, turning it on, to enter the direct recall
To set the transition time for an effect, downstream8 AUTO TRANS (automatic transition) button
mode. In this mode, pressing one of the PATTERN/
key, or fade-to-black, press this button, turning it on.Press this button to carry out an effect automatically.
KEY PAD buttons 0 to 9 recalls the corresponding
While it is lit, each time you press, the display windowWhen you press this button, the effect is carried out
snapshot 0 to 9.
mode indicators change. To set the transition timeautomatically, with the transition time which has been
corresponding to the display of the display windowset. During the transition this button is lit. Pressing this
mode indicators, enter the value using the pattern/button during the transition pauses it. Press the button4 DIRECT PATTERN button
Press this button, turning it on, to enter the direct
numeric keypad.once more to resume the transition.
If you set the fader lever to an intermediate positionpattern selection mode. In this mode, you can use the
PATTERN/KEY PAD buttons (0 to 9 and P IN P/
4 MIX buttonand press this button, the transition pauses at the
RST) to directly select the assigned effect patterns.
To carry out the next transition without applying anposition corresponding to the fader lever position.
When the system is powered on, and after exiting any
effect pattern, but as a mix, press this button, turning it
on.other operating mode, it automatically switches to
direct pattern selection mode.
DFS-700/700P
2-4Chapter 2 Location and Function of Parts and ControlsChapter 2 Location and Function of Parts and Controls2-5 |
ACEC
