Introductionfilter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal filter should be
These instructions are designed to tell you of the various technical details of your cooker hood and to make youreplaced.
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 2 and
familiar with its use. Since these instructions cover more than one type of hood within the same series, it may be
that reference is made to components that do not form part of the hood that you are installing. The hood may be3 temporary for more than 2 seconds:
- No flashing light of the bottom: less than 30 working hours
used as an exhaust or filter hood. If evacuation is available (exhaust duct or air flue) we recommend using the
- Flashing light of bottom 1: between 30 and 60 working hours
hood in the exhaust version to discharge all the kitchen vapors and odors out-doors. Fittings can vary from country- Flashing light of bottom 1 and 2: between 60 and 110 working hours
to country. We reserve the right to modify the product without any notice always with the aim of improvements
- Flashing light of bottom 1, 2 and 3: more than 110 working hours
and in compliance with the relevant norm.
Suggestions for using the hood in exhaust positionAfter you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more than
2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the Timer.
When an exhaust hood and a heat source requiring ambient air (e.g. gas, oil, coal stoves, etc.) are used at the
same time, attention is required because the air necessary for combustion is exhausted from the room throughSetting from Exhaust method into Filtering method (only for model HR - Fig.3B)
To get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting the cooker
the hood and this creates depression. There is no such danger when the maximum depression in the room is 0,04
hood into the proper method the electronic will adjust automatically the fan speed to the air resistance of the charcoal
mbar. In this condition no exhaust gas from the heat source is piped. To assure this condition, make openings in
the room which cannot be closed (doors, windows, etc. are not sufficient) and through which the air necessaryfilter.
Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the
for combustion can freely flow.
Note: ? All the exhaust ductwork in the apartment or house should be studied. In case of doubts, get advice orcooker hood will set to the exhaust method - confirm by flashing all buttons for 4 times.
Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood will set
authorization from the person or agency responsible for the building. When using gas burners, gas ovens, etc. as
to the filtering method - confirm by flashing all buttons for 8 times.
well as when using the hood in the filter version, these precautions are not necessary.
N.B. By reducting of the exhaust ducting and as well by increasing the length and numbers of elbows of the ductingNote: The cooker hood is set from the factory into the Exhaust method.
Operation light and function of saturation indication for the filters
the hood will lost on performance and could become noisy. When using the exhaust version, follow these rules:
Do not connect the exhaust hood to chimneys, flues, and air ducts serving the room. Before venting into exhaustHI (Fig. 3C) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood and
pushing the bottom T the operation LED will indicate different colours with following meanings:
flues and ducts no longer in use, ask for the approval of the person or agency responsible for the building. The
evacuated air must not be let into a warm air duct. For the evacuation of the exhausted air please note ufficialGreen Light: less than 6 working hours
Yellow Light: between 6 and 12 working hours
instructions.
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)
InstallationHR (Fig. 3B) - The saturation of the grease filter will be indicated automatically after 20 hours by means with flashing
The hood must be mounted over the center of the cooking area. The minimum distances between the cookingof the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual changed.
area and the underpart of the hood are 650 mm.It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 1 and
Warning: If the room contains a flued fuel burning appliance which is not of the "balance flue" type make sure3 temporary for more than 2 seconds:
these is an adequate air inlet to the room at all times so that fumes are not drawn down the flue.- No flashing light of the bottom: less than 6 working hours
N.B. The distances, however, are subject to the safety rules in effect in the various countries. Before drilling the- Flashing light of bottom 1: between 6 and 12 working hours
wall make sure that no pipes or cables will be damaged. If there is no outer waste-pipe for the exhaust version,- Flashing light of bottom 1 and 2: between 12 and 18 working hours
an air outlet with a diameter of 130 mm must be made through the wall.- Flashing light of bottom 1, 2 and 3: more than 18 working hours
Ceiling fixing of the cooker hoodAfter you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the main switch
1) Before installation, remove the tubes from the trellis (fig. 4/P-N). Decide at what height the hood is to be fitted,for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the
adjusting the Telescopic Trellis (Fig. 4/A) and fix it using the four screws provided (socket head, Fig. 4/B) throughTimer.
the housings provided, which have a 5 cm pitch (Fig. 4/C).If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the charcoal
2) If your hood is fitted with a metal carbon filter frame the mounting operation can be made more easily byfilter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal filter should be
removing it by means of the screws (Pict. 2/1) before beginning to work. The frame must be remounted whenreplaced.
the operation is finished.It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 2 and
3) Assemble the the spigot (Pict. 4/d) by means of the 2 screws (Pict. 4/E), fit only in recirculation version the T-3 temporary for more than 2 seconds:
connecting piece (Pict. 4/F). Mount the spigot on the upper part of the motorbox (Pict. 4/S) by means of the screws- No flashing light of the bottom: less than 30 working hours
(Pict. 4/H).- Flashing light of bottom 1: between 30 and 60 working hours
4) Fix the trestle to the ceiling by means of the screws and the plugs (Pict. 4/M). Look out not to damage either- Flashing light of bottom 1 and 2: between 60 and 110 working hours
wires or tubes and ensure that the power cord will pass from the ceiling to the inner part of the trestle upper- Flashing light of bottom 1, 2 and 3: more than 110 working hours
plate.After you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more than
5) Insert the inner tube (Pict. 4/N) into the trestle, push it to the ceiling and fasten it by means of the two screws2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the Timer.
(Pict. 4/O). Insert the outer tube (Pict. 4/P).Setting from Exhaust method into Filtering method (only for model HR - Fig.3B)
6) Fasten the hood to the Trellis using the 4 M6 screws (Fig. 4/Q), fitted from the inside of the hood. Complete electricalTo get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting the cooker
hook-up and fix the external pipe using the screws provided (Fig. 4/R), again working from the inside of the hood.hood into the proper method the electronic will adjust automatically the fan speed to the air resistance of the charcoal
N.B.: When using a 150mm air outlet, do not fasten the air outlet pipe with the screws, as this might cause the metal valvefilter.
to malfunction.Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the cooker hood will set
N.B.: In the case of recirculation fitting, join the flange and the T joint provided with 2 screws at the point marked with ato the exhaust method - confirm by flashing all buttons for 4 times.
line on the flange; this must all be done before fixing the hood to the wall.Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood will set
Electric connectionto the filtering method - confirm by flashing all buttons for 8 times.
Note ? A damaged power supply cord must be changed by the Service.Note: The cooker hood is set from the factory into the Exhaust method.
Make sure the supply voltage ratings correspond with those stated on the appliance data plate.Lamp Replacement
Attention: if the appliance is not provided with a plug or cannot be easily connected to a wall socket, then the electricalIt has a halogen lamp look out not to touch it with your hands when you replace it. Use a dry and not greasy
circuit must incorporate a circuit breaker having at least a 3 mm separation between contacts.protection (for example a cloth) in order to avoid a direct contact with skin which could make the lamp break. Never
Attention: This appliance must be connected to a system equipped with earth or ground place. The manufacturersuse lamps with a wattage higher than the one shown on the label inside the hood.
decline responsibility for problems caused by failure to observe this rule.
Safety rules
The wires in the supply cord are colored as follows:
green/yellow = ground ? blue = neutral ? brown = lineDo not do any flambe cooking underneath the hood. When frying, never leave the pan alone because the cooking
oil could flare up. Clean all the surfaces frequently to avoid danger of fire. To do so use a cloth and or brush soaked
Using the cooker hoodin denatured ethyl alcohol. It is also important to remove and clean or substitute frequently the filter installed in the
The cooker hood should be switched on either before or at the same as cooking or frying commences. The grease andhood.
carbon filters are more effective if the fan is not switched off immediately after cooking or frying is completed, but onlyMaintenance
after a period of some 20-30 minutes.
User instructionsNOTE: Prior to any maintenance, switch off and disconnect from electrical supply.
The cooker hood could be supplied with different operation panels (Fig. 3A-3B-3C) that works in the following way:1) Under normal cooking conditions the grease filter should be cleaned every 10-15 days in hot water, to which
Mechanical Switches (slide or pushbutton-Fig.3A)a suitable detergent has been added. For reasons of efficiency and safety regular cleaning is advised. The
grease filter may be subject to a small amount of shrinkage initially.
1 - Speed Switch2 - Light Switch
Back Lit Switches HR (Fig.3B)2) The outer casing of the Cooker Hood should be cleaned with a damp cloth.
- Main Switch 1-2-3 Speed Switches2 - Light Switch3) The effective life of the carbon filter will naturally depend on the frequency and type of cooking fumes to which
The Timer will run if any speed switch is pushed for more than 3 seconds and will stop running the cooker hood afterit is subject. As general guide we suggest that a replacement is fitted at least every 12 months.
5 minutes.4) Once a year, (more frequently with heavy usage), call a serviceman to clean the fan and air ducts to prevent
Multicolour Switches HI (Fig.3C)build-up of flammable fat deposits.
0/1-2-3 Speed Switches L - Light Switch T - TimerThe carbon filter
The Timer will run if the timer switch is pushed and will stop running the cooker hood after 5 minutes.When a carbon filter is fitted, the air that is sucked in is additionally cleaned by the active carbon particles within the filter.
Operation light and function of saturation indication for the filtersThis filter cannot be cleaned and so needs to be replaced from time to time, approximately every six months, depending
HI (Fig. 3C) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood andon how frequently the hood is in use.
pushing the bottom T the operation LED will indicate different colours with following meanings:Replacing the active carbon filter (only for recirculation hoods)
Green Light: less than 6 working hoursThe filter can be easily removed by pulling downwards the two knobs (pict. 2/2).
Yellow Light: between 6 and 12 working hoursGrease filter
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)This absorbs vapor-suspended grease particles and protects the kitchen and furniture from greasy residues. The filter
HR (Fig. 3B) - The saturation of the grease filter will be indicated automatically after 20 hours by means with flashingshould be washed every 10 to 15 days (in normal operating conditions). Dip the filter into a de-greaser solution or put
of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual changed.it in the dish washer. Make sure not to damage the filter, which is made of several layers of thin alloy, by hitting or crushing
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 1 andit. The aluminium filter will may change colour, that will have no influence of the efficiency of the filter, may it will improve
3 temporary for more than 2 seconds:it.
- No flashing light of the bottom: less than 6 working hoursReplacing or cleaning the filters
- Flashing light of bottom 1: between 6 and 12 working hoursTo remove the aluminuim grease filter (Pict. 1), grab the opening tongue at the filter, pull it in your direction and move
- Flashing light of bottom 1 and 2: between 12 and 18 working hoursthe filter downwards. To reinstall it operate reversed.
- Flashing light of bottom 1, 2 and 3: more than 18 working hoursSafety Requirements
After you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the main switchExhaust air must not be discharged into any chimney, or flue which may carry combustion products from other
for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically thesources. In addition, exhaust air must not be discharged into a wall cavity unless designed for the purpose. Note
Timer.instructions for cleaning fan as note ?4? on ?MAINTENANCE?. Moreover it is important to clean regularly each
If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the charcoalfilter of the hood or replace it. |