Refrigerator door
Door and Hinge Removal1. Remove the screw cover. See Graphic 6.
2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 6.
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown. See Graphic 3.
uD??" Hex-Head Hinge Screw
4. Remove door handle sealing screws. Move to opposite side of
1. Unplug refrigerator or disconnect power.refrigerator door as shown. See Graphic 4.
2. Keep both doors closed until you are ready to lift them free 5. Remove door handle seal screw front. Move to opposite side
from the cabinet.of refrigerator door as shown. See Graphic 7.
NOTE: Provide additional support for the doors while the 6. Remove door stop. Move to opposite side of refrigerator door
hinges are being moved. Do not depend on the door magnets as shown. See Graphic 5.
to hold the doors in place while you are working.7. Position refrigerator handle on opposite side of the refrigerator
3. Remove the parts for the top hinge as shown in Top Hinge door as shown. See Graphic 6. Drive top two screws in handle
first. Align lower portion of handle and drive bottom screw.
graphic.
4. Lift the freezer door free from the cabinet.8. Replace screw cover. See Graphic 6.
5. Remove the parts for the center hinge as shown in the Center 9. Tighten all screws. Set aside refrigerator door until bottom
Hinge graphic.hinge is installed on refrigerator.
6. Lift the refrigerator door free from the cabinet.
Door and Hinge Replacement
7. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
NOTE: Graphic may be reversed if door swing is reversed.
IMPORTANT: If you want to reverse your doors so that they open 1. Replace the parts for the bottom hinge as shown. Tighten
in the opposite direction, follow these steps. If you are not
reversing the doors, see ?Door and Hinge Replacement.?screws.
2. Replace the refrigerator door.
Door Reversal (optional)NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Assemble the parts for the center hinge as shown and tighten
all screws. See Center Hinge graphic.
Door Stop ScrewDoor Hinge Hole Plug4. Replace the freezer door.
5. Assemble the parts of the top hinge as shown. See Top Hinge
graphic. Do not tighten screws completely.
Door Handle Sealing ScrewCabinet Hinge Hole Plug6. Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.
Final StepsFlat-Head Handle ScrewDoor Handle Screw Cover
1. Check all holes to make sure that hole plugs and screws are in
place.
Door Handle Seal Screw Front Round-Head Handle Screw
Cabinet
WARNING
1. Remove uD??" hex-head hinge screws from handle side and
move them to opposite side. See Graphic 1-1.
2. Remove cabinet hinge hole plugs from cabinet top and
move them to opposite side hinge holes as shown.
See Graphic 1-2.
Freezer door
1. Remove freezer handle assembly as shown. Keep all parts
together. See Graphic 2.Electrical Shock Hazard
2. Remove door hinge hole plug. Move to opposite side as Plug into a grounded 3 prong outlet.
shown. See Graphic 3.
Do not remove ground prong.
3. Remove door handle sealing screws. Move to opposite side of
freezer door as shown. See Graphic 4.Do not use an adapter.
4. Remove door stop. Move to opposite side of freezer door as Do not use an extension cord.
shown. See Graphic 5.
5. Position freezer handle on opposite side of freezer door. Failure to follow these instructions can result in death,
Assemble handle on door as shown. See Graphic 2.fire, or electrical shock.
6. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.
2. Plug into a grounded 3 prong outlet.
3. Reset the controls. See ?Using the Control(s)? section.
7 |
ACEC
