Special Features
For this reason, the cycle will always be completed. If
Automatic Lint Filtering System
heavier fabrics in such out-of-balance loads should
The Lint Filtering System does not requireever contain excessive moisture at the completion of
cleaning.the cycle, redistribute the clothes in the washer and
Wash and rinse water is filtered and re-filteredreset the control dial for the final spin period.
continuously to trap lint shed by most fabrics during
the agitation cycle before it can be redeposited on theOverload Protector
wash load. The engineered hole design on the wash
basket in conjunction with water flow produced by theA built-in protector automatically shuts off the washer
motor in case of an overload. This can occur if:
agitator, traps lint away from the clothes between the
inner wash basket and the outer tub. Lint is automaticallyY The load being washed is too heavy.
flushed from the washer during the spin cycle.Y Too many appliances are plugged into the line
operating your washer.
Unbalanced Spin Y A low voltage condition exists on the line.
Y Lid is opened and closed repeatedly.
Load CompensatorThe overload protector permits the washer to start again
Your new washer is designed to handle out-of-balancewhen the motor has cooled to a safe operating temperature.
loads without shutting down or interrupting theIf the motor stops repeatedly, call your service technician.
washing cycle.
Care & Cleaning
1. After washing, leave the lid open until the interiorCleaning the Interior
is dry.
2. Check hoses to be sure there are no leaks, kinks orClean the interior of the washer periodically to remove
knots.any dirt, soil, odor, mold, mildew or bacteria residue
that may remain in the washer as a result of washing
3. Your washer should not be installed whereclothes. We recommend taking the following steps
temperatures will go below freezing, as damage to
the washer could result.every 60 to 120 days to clean and freshen your washer
4. To clean, occasionally wipe exterior with a clean dampinterior. The frequency with which the washer should
be cleaned and freshened depends on factors such as
sponge or cloth. Do not use polish on plastic parts.usage, the amount of dirt, soil or bacteria being run
5. Lifetime lubrication is done at the factory, so yourthrough your washer, or the use of cold water. Failure
washer never needs to be oiled or greased.
to follow these instructions may result in unsatisfactory
6. Do not lay heavy or sharp objects on top of yourconditions, including unpleasant odor and/or
washer.permanent stains on the washer or wash load.
7. The top of the washer should not be used for
removing stains from garments. Some stainTo clean and freshen the washer interior:
removers, such as rust remover, will mar the finish. 1. Add a measured amount of chlorine bleach to the
8. Remove pins, buckles or other sharp objects frombleach dispenser, following package directions.
clothes to prevent scratching interior parts.2. Add 1/4 cup of detergent to the tub.
9. Clothes should not be stored in washer.3. Run the washer without a load through a complete
10. Bleach, detergent, solvents, etc. spilled on the topcycle using hot water.
of your washer that are allowed to remain will4. Repeat the process if necessary.
remove the glossy finish. Remove all spills with a
damp, soft cloth.
11. If you close your home for the winter, have a service
technician drain the washer. Unplug cord from
electrical outlet and disconnect hoses from faucets.
9
Feats, lightsures
rarWe & cvierSleaningCe & arCtyeafStyanCycles, optionWhat can & washedoperating tipsSpecial cannot be asherw
niontInstalla the ginrtoSingkoCoveOtingooubleshortingkoCo efacrSudishwasher useloadingControls atDryer Exhaust tips a glanceNotes
tyeafSCycles, options,What can & washedoperating tipsSpecial lightsFeatures
Co efacrSurarWe & cvierSleaningCe & arCingkotyandishwasher usecannot be
iontInstalla the ginrtoSingkoCo nveOoubleshortasherwtingoloadingControls aDryer Exhaust tipst a glanNotcees |
ACEC
