INSTALLATIONMAINTENANCE AND CLEANING
Important
WarningBefore any maintenance or cleaning work is carried
Changing the light bulb
out, DISCONNECT the appliance from the
IF YOU ARE DISCARDING AN OLD APPLIANCEELECTRICITY supply.
It must be possible to disconnect the appliance fromShould the interior light fail to work, first switch off
THAT HAS A LOCK OR CATCH ON THE DOOR,
the mains power supply; the plug must therefore bethe appliance and disconnect from the electricity
YOU MUST ENSURE THAT IT IS MADE
easily accessible after installation.Internal cleaningsupply, then replace the bulb as follows;
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Clean the inside and accessories with warm water
Depending upon the position which you choose forand bicarbonate of soda (5ml to 0.5 litre of water).
your appliance, you may wish to reverse the way inRinse and dry thoroughly.
which the door opens. To do this, refer to instructions
on ?Door reversal directions?.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
Positioning
PRODUCTS OR WAX POLISHES, TO CLEAN
This appliance should only be installed at a location
THE INTERIOR AS THESE WILL DAMAGE THE
where the ambient temperature corresponds to the
SURFACE AND LEAVE A STRONG ODOUR.
climate classification indicated on the rating plate, which
Clean the drain hole of the water trough at regular
is located at the left on the inside of the appliance.
intervals and make sure that the drain hole is neverD411
The following table shows which ambient temperature is
obstructed, so that the defrost water may flow freely.
Unscrew the light cover and then pull it outward by
correct for each climate classification:
100 mmpressing as shown in the figure. Unscrew the bulb
SN +10°C to + 32°C
and replace it with a new 15 watt bulb (available
ABExternal cleaning
N +16°C to + 32°Cfrom your nearest Electrolux Service Force Centre).
Many proprietary kitchen surface cleanersReplace the light cover by sliding it into its original
ST +18°C to + 38°C
contain chemicals that can attack/damage theposition and replacing the screw.
10 mm10 mm
T+18°C to + 43°C
plastics used in this appliance. For this reason it
NP007
It should be located in a dry atmosphere, out of directis recommended that the outer casing of thisDefrosting
sunlight and away from extreme temperature e.g. not nextappliance is only cleaned with warm water with a
to a boiler or radiator, or in a very cold room e.g. anlittle washing-up liquid added. The refrigerator automatically defrosts every time the
outhouse, where the temperatures may fall below 10°Ccompressor stops. The water is discharged, via the
An accumulation of dust will affect the performance
pipe, into a tray located at the back of the appliance
(50°F). If these temperatures are exceeded i.e. colder or
of the appliance and cause excessive electricity
above the compressor, where it evaporates.
warmer, then the appliance may not operate correctly.consumption.
You should also ensure that air can circulate freely aroundYou MUST ensure that the appliance is switched
the back and the top of the cabinet. There must also be atOFF.
least 100 mm (4?) distance between the top of the cabinet
Once or twice a year dust the condenser (black grill)
and any overhanging kitchen furniture (A). Ideally, the
and the compressor at the back of the appliance,
appliance should not be positioned beneath overhanging
with a brush or vacuum cleaner, see diagram.
furniture (B).
There should also be a gap of 25 mm either side of the
appliance. Do not obstruct the space underneath. The
D200
back of the cabinet may be placed close to the wall but
must not touch it. DO NOT install in places with restricted
ventilation.
D037
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet using
Important
your fingers or a spanner (see figure).
To avoid defrost water overflowing into the fridge,
Rear spacersperiodically clean the water discharge hole in the centre
PR259
of the V shaped drip collector at the back of the
The plastic bag containing all relevantrefrigerator compartment behind the fruit and vegetable
documentation also contains two spacers to be fitted
drawer. Use the defrost cleaner provided which you will
When the appliance is not in use
into special holes in the back of the appliance.
Afind already inserted into the discharge hole.
Fit the spacers into the holes, taking care to ensureWhen the appliance is not in use for long periods,
45°Remember to wash the defrost cleaner in hot soapy
that the arrow (A) is positioned as shown in thewater at regular intervals. Dry throughly beforedisconnect from the electricity supply, empty all
PR60
diagram. Then turn them through 45° (arrow (A)foods and clean the appliance, leaving the doors ajar
replacing.
vertical) until they lock into place.to prevent unpleasant smells.
107 |
ACEC
ELECTROLUX
