FM TUNERFM TUNER
Switching radio on/offStoring radio stations
Y Press FM/ once or more to switch the radio on/You can store up to 30 radio stations. Select a preset
number 1-30.
off.
� Display shows briefly Radio on or Radio off1Tune to a desired radio station and press PROG
respectively.briefly.
Use the remote control or set to tune to any FM station 2Press PROGwhile PROGis blinking to confirm the
automatically or manually.storage.
�PROG, the FM frequency and the preset number of
Tuning to radio stations automaticallythe stored station are displayed.
1Press and hold or §for at least 2 seconds.3Store all desired stations this way.
� Display shows briefly Searching.The radio tunes
to a station with sufficient strength and radio play
starts. The FM frequency is displayed.Helpful Hint:
2Repeat searching until you find the desired radio station.Already stored stations can be recognized by a preset
number.
Tuning to radio stations manually
1Keep or §pressed.
2Release or §, then briefly press or §againTuning to a stored radio station
when you are close to the desired frequency.1Press ALBUM +/ -repeatedly if necessary to select
3Briefly press or §repeatedly until you reach thethe preset number of the desired radio station.
desired frequency.� Radio play starts. The FM frequency and the pre-
� Radio play starts. The FM frequency is displayed.set number (P1-30) of the stored station are dis-
played.
YTo switch from radio play to CD play, press 2;.
Y Press to switch the radio off.
Helpful Hint:
� To improve reception: The headphone wire is used as an FM antenna.
If necessary, move it for optimum reception.
� Tuner operation is not affected if you open the CD lid to change a disc.
LOCKTROUBLESHOOTING
You can lock the buttons of the set/ remote control respectively by switching theWARNING: Under no circumstances should you try to repair the unit yourself as
slider to LOCK. With LOCK activated, you can avoidthis will invalidate the warranty. If a fault occurs, first check the points listed,
accidental activation of other functions.before taking the unit for repair. If you are unable to solve a problem by following
1Switch the slider toLOCKto activate LOCK.these hints, consult your dealer or service center.
� All buttons are locked. Hold is shown when you
The CD player has no power, or playback does not start
press any button on the set / remote control
respectively. If the set is locked and switched off, Hold will be shownY Check that your batteries are not dead or empty, that they are inserted
only when pressed 2; .correctly, that the contact pins are clean.
YYour adapter connection may be loose. Connect it securely.
2To deactivate LOCK, switch the slider to OFForUNLOCK.
The indication Please insert CD is displayed
Y Check that the CD is clean and correctly inserted (label-side upward).
Y If your lens has steamed up, wait a few minutes for this to clear.
The indication Unfinalized CD is displayed
Y CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
ENVIRONMENTAL INFORMATION
The indication Hold is on and/or there is no reaction to controls
Y All redundant packing material has been omitted. We have done our utmost toY If LOCK is activated, then deactivate it.
make the packaging easily separable into two materials: cardboard (box) andY Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
polyethylene (bags, protective foam sheet).
The CD skips tracks
YYour set consists of materials which can be recycled if disassembled by a Y The CD is damaged or dirty. Replace or clean the CD.
specialized company. Please observe the local regulations regarding the Y, or PROG is active. Switch off whichever is on.
disposal of packing materials, dead batteries and old equipment.
No sound or bad sound quality.
Y pause might be active. Press 2;.
Y Loose, wrong or dirty connections. Check and clean connections.
YVolume might not be appropriately adjusted. Adjust the volume.
Y Strong magnetic fields. Check playerOs position and connections. Also keep
away from active mobile phones. |
ACEC
PHILIPS
