8ENGLISH
�Please bear in mind that the fragrance level depends on a number of factors, such as the following:
- Habituation may cause fragrances to be perceived less or not at all, but this is normal.
- When you lie on your belly, the fragrance will be less noticeable than when you are lying on your back.
- Airflows in the room where you use the appliance may also affect the fragrance level.
- Your personal condition may also influence the degree in which you perceive the fragrance.
Stereo Active Speakers & Nature sounds (HB935 only)
During tanning or relaxing, you can choose a nature sound that appeals to you and that helps you relax optimally.There are four different nature
sounds to choose from.
You can also listen to your own favourite music by connecting your own audio player (e.g. CD/MP3 or radio) to the INNERGIZE.
� You can adjust the volume by pressing the + or - button (fig. 29).
� To enhance the spatial quality of the sound, press the Surround button.The pilot light will go on (fig. 30).
� To listen to the sounds undisturbed by other background noises, you can use the in-ear headphones that come with the appliance.
Listening to nature sounds
On the dial below the timer buttons you can select four sounds.
1 Press the button below the dial to select a sound (fig. 31).
- The pilot light corresponding to the selected sound goes on.
- Each time you press the button, the next pilot light will go on to indicate that the next sound has been selected.
After you have made your choice, the appliance will play the sound.
� Nature sounds are meant to be background sounds.This means that they should not be too dominant.The relaxing effect is optimal
when the sounds are just audible.Avoid high sound levels.
Listening to your own favourite music
To connect your own audio player (e.g. CD/MP3 or radio) to the appliance use the cable with 2 jack plugs supplied with the appliance.
1 Insert one jack plug into the AUX socket on the right side of the control panel.
2 Insert the other jack plug into the headphone socket of your audio player (e.g. CD, MP3 or radio).
3 Select position 'Aux' (fig. 32).
The Philips Stereo Active Speakers will amplify the signal according to your preference.
Cleaning
Always unplug the appliance and let it cool down before you start cleaning it.
Never use abrasive liquids like scouring agents, petrol or acetone to clean the appliance. Do not use scouring pads.
� Clean the outside of the appliance with a damp cloth.
Do not let any water run into the appliance.
� You can clean the outside of the UV filters with a soft cloth sprinkled with some methylated spirits.
Storage
Let the appliance cool down for 15 minutes before you put it in transport position and store it.
� You can store the protective goggles in the storage compartment between the two lamps (fig. 33).
1 Make sure the cord does not get stuck between parts of the appliance when you put the appliance in transport position.
2 Turn the appliance away from the bed or sofa and make sure there is enough space around the appliance to collapse it.
3 Press the two release buttons in the recesses of the control panel and slide the control panel down the stand as far as it goes (fig. 34).
4 Turn the lamp unit in the direction of the arrow (fig. 35).
You will hear a click when the lamp unit locks in vertical position.
5 Pull the stand slightly backwards, then press the dual push button and lower the stand slowly until the lamp unit rests on the floor
between the legs (fig. 36).
6 Wind the cord and fasten it with the cord wrap strip (fig. 39,40,41).
� You can store the appliance in a wardrobe or under a bed.
Replacement
The light emitted by the tanning lamps will become less bright in time (i.e. after a few years in case of normal use).When this happens, you will
notice a decrease in the tanning capacity of the appliance.You can solve this problem by setting a slightly longer tanning time or by having the
tanning lamps replaced.
� The appliance has a counter that records the operating hours of the tanning lamps (HB935 only).
1 Select function ". Set the time to 00 and press the pause/repeat § button at least 2 seconds to make the operating hours appear on
the display.The maximum number of hours that can be displayed is 999.When this value has been reached, the counter will start
counting up from 000 again.
2 The operating hours will disappear from the display as soon as the pause/repeat § button is released. |
ACEC
PHILIPS
