Operation Guide 3750
World Time3. When the setting you want to change is flashing, use B and D to change it as
described below.
World Time digitally displays the current time in 27 cities
Current time for the (29 time zones) around the world.SettingScreenButton Operation
selected city code
" All of the operations in this section are performed in theStart TimeUse D (+) and B (�) to change the setting.
World Time Mode, which you enter by pressing C." You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
To view the time in another cityAuto-repeatPress D to toggle auto-repeat on ( displayed) and off
In the World Time Mode, press D to scroll eastwardly( displayed).
through city codes.Progress BeeperPress D to toggle the progress beeper on (ON) and off
" For full information about city codes, see the OCity Code(OF).
City code Table�.
" If the current time shown for a city is wrong, it probably4. Press A to exit the setting screen.
means there is a problem with your Timekeeping Mode" You can also perform steps 1 and 2 of the above procedure whenever you need to
time and/or Home City code settings. Go to theview the current auto-repeat and progress beeper settings.
Timekeeping Mode and make the necessary
adjustments.To use the countdown timer
Press D while in the Countdown Timer Mode to start the
To toggle a city code time between Standard Time and Daylight Saving Timecountdown timer.
1.In the World Time Mode, use D to display the city code" The countdown timer operation continues even if you
whose Standard Time/Daylight Saving Time setting youexit the Countdown Timer Mode.
want to change." Press D while a countdown operation is in progress to
2.Hold down A for about two seconds to toggle betweenpause it. Press D again to resume the countdown.
Daylight Saving Time (DST indicator displayed) and" To completely stop a countdown operation, first pause it
Standard Time (DST indicator not displayed).(by pressing D), and then press A. This returns the
" The DST indicator is on the display whenever youcountdown time to its starting value.
DST indicator display a city code for which Daylight Saving Time is
turned on.
" Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are notStopwatch
affected.
The stopwatch lets you measure elapsed time, split times,
" Note that you cannot switch between Standard TimeSeconds
and two finishes.
and Daylight Saving Time while GMT is selected as the
city code.1/100 " The display range of the stopwatch is 59 minutes,Minutes seconds
59.99 seconds.
" The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
Countdown Timer" The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
The countdown timer can be set within a range of one" Exiting the Stopwatch Mode while a split time is frozen
Minutes Seconds minute to 60 minutes. An alarm sounds when theon the display clears the split time and returns to
countdown reaches zero. The countdown timer also haselapsed time measurement.
an auto-repeat feature and a progress beeper that signals" All of the operations in this section are performed in the
the progress of the countdown.Stopwatch Mode, which you enter by pressing C.
" All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
To measure times with the stopwatch
C.
Elapsed Time
Configuring the Countdown Timer
The following are the settings you should configure beforeStartStopRe-startStopClear
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; ProgressSplit Time
beeper on/off
" See OTo configure the countdown timer� for information
about setting up the timer.StartSplitSplit releaseStopClear
Auto-repeatTwo Finishes
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeatedStartSplitStopSplit releaseClear
a total of eight times, after which it stops automatically.First runner Second runner Display time of
When auto-repeat is turned off, the countdown stops when it reaches zero and thefinishes.finishes.second runner.
display shows the original countdown start time.Display time of
" Pressing D while an auto-repeat countdown is in progress pauses the currentfirst runner.
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.
Countdown Timer Beeper OperationsAlarms
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes theYou can set five independent Daily Alarms. When an
On/Off status
types of beeper operations the watch performs during a countdown.alarm is turned on, the alarm tone sounds when the alarm
Alarm timetime is reached. One of the alarms is a snooze alarm,
Countdown End Beeper(Hour : Minutes) while the other four are one-time alarms.
The countdown end beeper lets you know when the countdown reaches zero.You can turn on an Hourly Time Signal that causes the
" When the progress beeper is turned off, the countdown end beeper sounds forwatch to beep twice every hour on the hour.
about 10 seconds, or until you press any button to stop it." There are six screens in the Alarm Mode. Four are for
" When the progress beeper is turned on, the countdown end beeper sounds forone-time alarms (indicated by numbers from
about one second.AL1through AL4), one is for a snooze alarm
Progress Beeper(indicated by SNZ), and one is for the Hourly Time
When the progress beeper is turned on, the watch uses beeps to signal countdownAlarm number Signal (indicated by SIG).
progress as described below." All of the operations in this section are performed in the
" Starting from five minutes before the end of the countdown, the watch emits fourAlarm Mode, which you enter by pressing C.
short beeps at the top of each countdown minute.
" 30 seconds before the end of the countdown, the watch emits four short beeps.To set an alarm time
" The watch emits a short beep for each of the last 10 seconds of the countdown.1.In the Alarm Mode, use D to scroll through the alarm
" If the countdown start time is six minutes or greater, the watch emits a short beep forscreens until the one whose time you want to set is
each second of the final 10 seconds before the five-minute point is reached. Fourdisplayed.
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
" To set a one-time alarm, display one of the screens indicated by an alarm number
setting screen.
from AL1through AL4. To set the snooze alarm, display the screen indicated
" If the countdown start time is not displayed, use the
procedure under OTo use the countdown timer� toby SNZ.
" The snooze alarm repeats every five minutes.
display it.
2. After you select an alarm, hold down A until the hour setting of the alarm time
2. Press C to move the flashing in the sequence shown
below to select other settings.starts to flash, which indicates the setting screen.
" This operation automatically turns on the alarm.
Start TimeAuto-repeat3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (�) to change it.
" When setting the alarm time using the 12-hour format, take care to set the time
Progress Beeper
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
2 |
ACEC
