Before use
The current level is indicated by the number of flashes
Before using your dishwasher for the
made by the push bu1ttonindicator light, that alternates 5
first time:seconds off with a number of flashes, this for about 60
1.Ensure that the electrical and water connections comply seconds.
with the installation instructionsExample:
2.Remove all packaging from inside the appliance1 flash= level 1
2 flashes = level 2
3.Set the water softener
3 flashes = level 3
4.Pour 1 litre of water inside the salt container and then fill
4 flashes = level 4
with salt
5 flashes = level 5
5.Fill the rinse aid dispenser.
4.To change the level, press the programme 1push .button
Each time the push button is pressed the level changes.
Setting the water softener
Example:
The dishwasher is equipped with a water softener designed If the tocurrent level is 3, by pressing the programme push
remove minerals and salts from the water supply, which button would1 once, level 4 is selected.
have a detrimental or adverse effect on the operation of the
If the current level is 5, by pressing the programme push
appliance.
button 1 once, level 1 is selected.
The higher the content of these salts, the harder your water is.
The push button 1 indicator light remains off for about
Water hardness is measured in equivalent scales, German
5 seconds after which it starts flashing indicating the
degrees, French degrees and PPM (parts per Million).
new level selected.
The softener should be adjusted according to the hardness of
the water in your area.Your local Water Authority can 5.Toadvise memorise the new level, switch off the dishwasher by
you on the hardness of the water in your area.pressing the On/Offpush button.
Water hardness
Filling with salt
LevelGermanFrenchPPMUse of
degrees degrees(Parts per saltOnly use salt specifically designed for use in
(°dH)(°TH)Million)
dishwashers.
1< 4< 8< 80NOAll other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
24 - 188 - 3081 - 300YES
softener.
319 - 2931 - 50301 - 500YESOnly fill with salt just before starting one of the complete
washing programmes. This will prevent any grains of salt
430 - 4051 - 70501 - 700YES
or salty water, which may have been spilled, remaining on
541 - 5071 - 90701 - 900YES
the bottom of the machine for any period of time, which
may cause corrosion.
The dishwasher is factory set at level 3.
If this level is not suitable for your area the softener should be
adjusted.To fill:
1.To fill with salt, unscrew the cap of the salt container.
To select a different level be sure 2.thatPour 1 litre of water inside the thiscontainer is necessar( y
only before filling with salt for the ). first time
the dishwasher is off and then proceed
3.Using the funnel provided,
as follows:
pour in the salt until the
SALE
1.Press 1 and 3 programme push buttons simultaneously.container is full.SALT
Do not worry if water over SALZ
SEL
2.While keeping the programme push 1buttons and 3flows from the unit when
pressed switch on the dishwasher by pressing On/Off the filling with salt, this is quite
push button .The On/Offindicator light comes on.normal.
At the same time the programme push 1 banduttons 34.Replace the cap making
start flashing.sure that there is no trace
of salt on the screw thread
3.Press the push bu1tton , the indicator light of the push or on the gasket.SR14
button 3 turns off, while the indicator light of the push
5.Screw on the cap tightly.
button1 remains fixed for about 5 seconds and then starts
flashing indicating the current level of the water The softenersalt container .will require
topping up periodically.
The salt cap has a refill
indicator window in the
centre.
A green floatis clearly
visible when there is salt
inside the container, and
almost disappears when the
salt has finished reminding
SR11
SO462you to add salt.
5 |
ACEC
