" Do not place carbonated or fizzy drinks in the" There are working parts in this product whichChanging the opening direction of
freezer as it creates pressure on the container,heat up. Always ensure that there is adequate
the doors
which may cause it to explode, resulting inventilation as a failure to do this will result in
damage to the appliance. Do not use acomponent failure and possible food loss. See
Before carrying out any operations, remove the plug
installation instructions.
from the power socket.mechanical device or any artificial means to
speed up the thawing process other than those
To change the opening direction of the door," Parts which heat up should not be exposed.
recommended by the manufacturer. Never use
proceed as follows:Wherever possible the back of the product should
metal objects for cleaning your appliance as it
be against a wall.
1. pull off the ventilation grille (D) which is clipped
may get damaged.
into place;
2. remove the bottom hinge (E) by unscrewing itsInstallationEnvironment Protection
fixing screws;
" During normal operation, the condenser and
This appliance does not contain gasses which
3. remove the lower door, sliding it out of the
compressor at the back of the appliance heat up
could damage the ozone layer, in either its
middle hinge;
considerably. For safety reasons, minimum
refrigerant circuit or insulation materials.The
4. unscrew the middle hinge (H);ventilation must be as shown in the instructions.
appliance shall not be discarded together with
5. remove the upper door, releasing it from theAttention: keep ventilation openings clear ofthe urban refuse and rubbish. Avoid damaging
upper pin (G);
obstruction.the cooling unit, especially at the rear near the
6. unscrew the upper pin (G) and refit it on theheat exchanger. Information on your local
" Care must be taken to ensure that the appliance
opposite side;disposal sites may be obtained from municipal
does not stand on the electrical supply cable.
authorities.The materials used on this appliance
7. remove the two plugs of the door (where
Important: if the supply cord is damaged, it mustmarked by the symbol are recyclable.
available), discovering the holes for the hinge
be replaced by a special cord or assembly availa-
pins, assemble them on the opposite side and
ble from the manufacturer or its service agent.
refit the upper door;
" If the appliance is transported horizontally, it is
8. reassemble the middle hinge on the opposite
possible that the oil contained in the compressor
side;
flows in the refrigerant circuit. It is advisable to
9. reassemble the lower door;
wait at least two hours before connecting the
10. using a 10 mm spanner, unscrew the hinge pinappliance to allow the oil to flow back in the
(E) and reassemble it on the opposite side of thecompressor.
hinge;
11. reassemble the lower hinge (E) on the opposite
side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
12. refit the ventilation grille (D), clipping it into
place.
CONTENTS
13. Unscrew the handles. Re1t them on the
opposite side.Warnings ................................................................................................................................................. 2
Use - Cleaning the interior - Control panel - Freezer section ................................................................... 4
To line up the doors, it is possible to adjust the
Use - Startup and temperature adjustment - Freezing fresh food - Conservation of deep-frozen food ....
middle hinge (H) horizontally by means of a tool,
after slackening the two screws (see figure).Ice-cube production - Thawing .................................................................................................................. 5
Use - Fridge section - Startup and temperature adjustment - Fresh food refrigeration - Movable shelves 6
Warning:
Use - Positioning the door shelves- Bottle holder - Drawer - Humidity control ......................................... 7
After having reversed the opening direction of
Hints - Hints for refrigeration - Hints for freezing - Hints for storage of frozen food ................................. 8
the doors check that all the screws are properly
Maintenance - Periodic cleaning - Periods of non-operation - Illumination lamp...................................... 9
tightened and that the magnetic seal adheres to
the cabinet. If the ambient temperature is cold (i.e.Maintenance - Defrosting ....................................................................................................................... 10
in Winter), the gasket may not fit perfectly to the
Noisinnes - Customer service and spare parts ................................................................................... 11
cabinet. In that case, wait for the natural fitting of the
Technical information / Installation - Location - Shelf holders............................................................... 12
gasket or accelerate this process by heating up the
part involved with a normal hairdrier.Installation - Rear spacers - Electrical connection................................................................................... 13
Installation - Changing the opening direction of the doors....................................................................... 14
143 |
ACEC
