Dimension12
Dimension12
SAMPLE BANKS
FRONT PANEL FUNCTIONS
1
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1. INPUT LEVEL KNOB controls the amount of signal that enters the D12
2. RECORD BUTTON engages the record function of the D12
3. PLAY BUTTON plays the sample in the D12Os currently selected bank
4. STOP BUTTON stops the sample in the D12Os currently selected bank
When sampling, the capabilities of the D12 are as follows:5. GATE/REVERSE activates the gate or enables sample to be played backwards. In
4 six second samples, only bank1&2 or 3&4 are playable simultaneouslydelay mode it engages reverse delay function. .
2 twelve second samples, only 1 twelve second sample playable at a time.6. STUTTER places a marker in the sample to return to every time the button is pushed
7. DATA WHEEL enables you to find specific points in the sample for easier editing. In
2 six second samples, and 1 twelve second sample can be stored in mem-
delay mode it selects delay time.
ory. Only the 2 six second samples can be played simultaneously. It may
8. EDIT BUTTON enables you to place start/stop points within the sample
be easier to think of bank 1&2 and bank 3&4 as seperate sample groups.9. DISPLAYshows a numeric time index of the sample. In delay mode it shows
Only one Ogroup� can play at a time, whether it is 2 six second samples, ordelay time
1 12 second sample.10. BANK 1 accesses 6 seconds of sampling in bank 1
11. BANK 2 accesses 6 seconds of sampling in bank 2
NOTE you must press both banks together to select a 12 second sample.
Selecting both bank 1 and bank 2 accesses 12 seconds of combined sampling
If you have selected a twelve second sample, and accidentally press a sin-
12. BANK 3 accesses 6 seconds of sampling in bank 3
gle bank button, the sample will be lost.13. BANK 4 accesses 6 seconds of sampling in bank 4
Selecting both bank 3 and bank 4 accesses 12 seconds of combined sampling
WARRANTY14. LOOP BUTTON Enables sample to start playing again when it reaches its end point.
When engaged the sample will play continuously until button is pressed again.
1. The warranty registration card must be mailed within ten days after pur-15. DELAYBUTTON Places D12 in delay mode
chase date to validate the warranty of this DOD product.16. TAP TEMPO BUTTON Tapping this button in time with the music enables you to set
the delay time in time with the music.
2. DOD warrants this product (1 year parts, 1 year labor ), when used sole-17. EFFECTON/OFF BUTTON Engages the LFO for effects ranging from subtle
ly within the U.S., to be free from defects in material and workmanshipchorusing to jetlike flanging.
under normal use and service.18. SPEED KNOB Controls speed of LFO
19. DEPTH KNOB Controls depth of LFO
3. DOD Electronics liability under this warranty is limited to repairing or
20. FEEDBACK KNOB Controls amount of feedback
replacing defective materials that show evidence of defect, provided the
21. MIX KNOB Blends between dry signal and effect
product is returned through the original dealer, or an authorized DOD
sevice center where all parts and labor will be covered up to a period of
one (1) year. The company shall not be responsible for any consequentialREAR PANELFUNCTIONS
damage as a result of the products use in any circuit or assembly.
4. Proof of date of purchase is considered to be the burden of the consumer.
5. DOD reserves the right to make changes in design or make improvements
upon this product without incurring any obligation to install the same on
PRODUCTS PREVIOUSLY MANUFACTURED. 1 2 3 4 5 6 7
1. MIDI IN JACK Plug your MIDI controller in here (optional)
6. The foregoing is in lieu of all other warranties, either expressed or implied,
2. FOOTSWITCH INPUT Connect in the DOD FS3M here (optional)
and DOD neither assumes nor authorizes any person to assume any
obligation or liability in connection with the sale of this product. In no event3. A.C. ADAPTER INPUTConnect in the DOD PS750 in here
shall DOD or its dealers be liable for special or consequential damages or4. MONITOR OUTPUTConnect to mixer/pre-amp/amp input.
from any delay in the performance of this warranty due to causes beyond5. MAIN OUTPUTConnect to mixer/pre-amp/amp input.
their control.6. MAIN INPUT (STEREO) Connect output from sample source here
7. MIC INPUT (HI-Z) Connect microphone here |