You can also turn ORhythm� on by setting the TEMPO, As an alternative to using the CH ON/SOLO key to select so-
OSetUp� tab page parameter Rhythm Assign to Monitor. lo, you can press a button in the MIXER, SOLO/MONITOR,
OSolo� tab page. This method allows you to select a Send or
(3) Adjust the monitor volume.
Song, Locate
Return signal for soloing, as well as the signal of a channel
The monitor volume is adjusted by the MONITOR
(? p.113).
LEVEL knob for the MONITOR OUT L/R jacks, and by
the PHONES VOLUME knob and MONITOR LEVEL
for the PHONES jacks.Soloing more than one channel
(1) Access the MIXER, SOLO/MONITOR, OSolo� tab MixerMixer
page.
3-8. Adjusting the cue level
(2) Use the Mode radio buttons to select OMix.�
Cue Level is a function that lets you adjust the monitor vol-
(3) Use steps (3) and (4) in OSoloing just one channel�
ume and pan independently of the settings of the master bus.
(above) to select the channels that you want to solo.
The cue signal is output from the MONITOR OUT L/R jacks Effects
and the PHONES jacks.
Cancelling solo
(1) Select cue as the source for monitoring.
In the MIXER, SOLO/MONITOR, OMonitor� tab page, (1) Access the MIXER, SOLO/MONITOR, OSolo� tab
select OCue� and turn it on (highlighted).page, and turn off the button(s) that you selected for
soloing.Rhythm
If you have made OSolo� settings, defeat OSolo� before you
If you want to clear all solo settings, press the Clear All
select Cue.
button.
(2) Adjust the cue level.
You can also cancel Solo by setting the CH ON/SOLO mode
Access the MIXER, SOLO/MONITOR, OCueLevel� tab
key to CH ON mode.
page. Select the icon for each channel, and use the
Recorder
buttons to adjust the volume level and pan. You (2) Verify the setting.
can also use the value dial or the +/� keys to make your In the OMonitor� tab page, verify that Solo is now off.
selection.
Sending the soloed audio from the master bus
D16XDIf you want to, you can send the soloed audio signal to the
MASTER OUT L/R jacks. Use this when you want to hear
the soloed audio through the monitor system connected to
the MASTER OUT L/R jacks.Operation
In the MIXER, SOLO/MONITOR, OSolo� tab page, turn the
Solo? Master button on (highlighted).
D32XD
CD
3-10. Muting a channel
You can use the CH ON/SOLO keys to mute individual
channels.
(1) Set the CH ON/SOLO mode key to CH ON.
The CH ON/SOLO keys of all channels will light.
Data
(2) When you press the CH ON/SOLO key of a channel, it
will be muted (the key will be dark).
Drive
3-9. Solo settings
Use the Solo function when you want to listen to only a spe-
USB
cific channel(s) without affecting the signal being recorded or
sent to the MASTER L/R bus. You can also use the solo when
you want to listen to one of the Send signals or to one of the
Return signals from one of the internal master effects. The
solo signal is output from the MONITOR OUT L/R jacks and
MIDI
the PHONES jacks.
Soloing just one channel
(1) Access the MIXER, SOLO/MONITOR, OSolo� tab
page.
Upgrading the system
(2) Use the Mode radio buttons to select OLast.�
(3) Press the CH ON/SOLO mode key to select SOLO
mode (key lit orange).
The CH ON/SOLO keys of all channels will blink.
(4) Press the CH ON/SOLO key for the channel you want Touch Panel Calibration
to solo.
The key of the selected channel will continue blinking,
and the keys of the other channels will go dark.
(5) Listen to the soloed signal.
51 |
ACEC
