? Was the inserted laundry too wet (Washing
PREPARING THE LAUNDRYSELECTING A DRYING TIME OR FILTER
machine spin speed less than 800 rpm? When
PROGRAMME AND OPTIONS
1. Check that all fastenings are closed and that Clean the lint filter at the end of every the spinning speed is less than 800 rpm the
drying cycle:
pockets are empty. Drying Time or Programme and Options:water container fault may occur during drying
? To select a drying time or a programme, turn 1. Open the door.
2. Turn the articles inside out.cycle).
3. Place laundry loosely in the drum to make the time selector knob clockwise.2. Pull the filter upwards.? Is the lint filter dirty (filter indicator lamp on)?
3. Open the filter.
sure it doesn?t become tangled.? To select an option (if available), press the ? Is the heat exchanger dirty? (refer to the
4. Remove lint using a soft brush or your
corresponding button.Instructions for use)
Sort laundry as follows:fingertips.? Is the ambient temperature too high?
?Press the button again to cancel the option.
A) By care symbols 5. Close the filter.The dryer does not operate:
(on the collar or inside seam):6.Push the filter firmly back into place.STARTING AND COMPLETING A ? Is the power plug properly inserted into the
Suitable for tumble dryingDRYING CYCLEmains electricity socket?WATER CONTAINER BOTTOM
? Is there a power failure?
1. Having selected the desired drying time or Empty the water container at the end of ? Has the fuse blown?
Tumble drying with reduced drying programme and options, press the Start ? Is the door properly closed?
every drying cycle.
intensity onlybutton.? Has the drying time been selected?
1. Pull the handle to remove the water
If the laundry is not removed at the end of ? Has the Start button been pressed?
Do not tumble drycontainer.
the drying cycle, an automatic anti-crease 2. Empty the water container.Lint filter or water container indicator lamp
B) By amount and thickness/weightcycle ?? will operate for maximum 3. Replace the water container when empty by on:
Whenever the load to be dried exceeds 12 min. pushing it completely back in place.
? Is the lint filter clean?
dryer capacity, separate laundry according to 2. On completion of the drying cycle, set the ? Is the water container empty?
weight (e.g. towels from thin underwear).time selector knob to position ?0?.INSTALLATION STABILITY? Is the water container correctly positioned?
C) By type of fabrics3.The dryer indicator lamp ?On? switches off.When installing your dryer, always carefully ? Is the heat exchanger clean?
Cotton/linen: Towels, cotton jersey, bed level the dryer using the adjustable feet and Water droplets underneath the dryer:
INTERRUPTING A DRYING CYCLE
and table linen made of cotton or linen.check the correct levelling with a spirit level.? Is the heat exchanger correctly positioned?
Synthetics/Easy Care: Blouses, shirts, To interrupt the dryer during operation? Has any fluff on the heat exchanger seal been
overalls, etc. made of polyester or wiped away?HEAT EXCHANGER
1. Set the time selector knob to ?Airing?.
polyamide, as well as cotton/synthetic ? Has any fluff on the door seal been wiped
2. Wait at least 5 minutes before opening the Clean the heat exchanger at least every 3
mixes.months. Wipe away any lint/fluff from the away?
door to allow the dryer to cool down.?Has the water container been positioned
D) By drying leveldoor seal and interior using a damp cloth.
For your safety the drying cycle stops correctly?
? Sort into: iron dry, cupboard dry, etc.(Please refer to instructions for use)
automatically if you open the door.
Do not tumble dry: Woollens, silk, nylon 3. To restart, after door opening, close the door AFTER-SALES SERVICE
BUILT-IN INSTALLATION
stockings, delicate embroidery, fabrics with and press the start button again.
If, after carrying out the above checks the
metallic decorations, bulky items such as sleeping To built in the dryer (when absolutely
malfunction persists or appears again, turn
bags, etc.necessary)
the dryer off and call our After-Sales Service
Important: only use specific indicated dryer-1. It is recommended to not remove the (refer to guarantee).
worktop.
safe additives and rinse items that have been Please specify:
2. A minimum space of at least 5 cm between
treated with stain remover thoroughly in plenty ? the nature of the fault.
of water before drying. Only use specific the dryer and the furniture is necessary to ? the dryer type and model.
guarantee the correct airflow.
indicated dryer-safe plastic items and never ? the service code (the number after the word
dry rubber or articles contaminated with Service on the adhesive rating plate) on the
TROUBLESHOOTING GUIDE
vegetable oil in the dryer.right hand side when the door is open.
If a fault occurs, before contacting our?your full address and phone number.
After-Sales Service, make the following
checks to try and remedy the problem:
Drying takes too long / laundry is not dry
enough:
? Was the correct drying time selected?
5019 607 00513 |
ACEC
