Progressive videoPage
There is ghosting when eThis problem is caused by the editing method or material used on DVD-Video, but should be 12
progressive or HDMI output is corrected if you use interlace output. Change ?Video Output Mode? in Picture Menu to ?525 (480)i?
on.or ?625 (576)i?.
When connecting with HDMI AV OUT terminal, connect with the other terminals and change the
settings in the following order:
1.Select ?HDMI Video Mode? to ?Off?.15
2.Select ?Video Output Mode? to ?525 (480)i? or ?625 (576)i?.12
Pictures not in progressive output. eIf the unit is connected to the television through VIDEO OUT or S VIDEO OUT, output will be interlace.-
Sound incorrect
Sound distorted.eSet ?Advanced Surround? in Audio Menu to ?Off?.13
eSet ?Attenuator? in Audio Menu to ?On? if it causes distortion with 2 ch or 5.1ch AUDIO OUT connections.13
eNoise may occur when playing WMA.-
eThe disc may have restrictions on the method of audio output. With some multi-channel discs, unless -
the number of connected speakers is the same as the disc?s channel specification, audio will not be
output properly. Refer to the disc?s jacket for more information. [DVD-A]
eWith HDMI AV OUT connections, audio may not be output from other terminals in the way that was set.-
eMatch the speaker settings with the connected equipment.14
eWhen connecting to an amplifier with the HDMI cable, match the speaker settings on this unit and the 15
amplifier with the presence and size of connected speakers.
Piercing noise comes from the eIf you have connected a digital amplifier which does not include decoder, be sure to select ?PCM? 14
speakers.in ?Dolby Digital?, ?DTS Digital Surround? or ?MPEG? in ?Audio? tab.
Effects do not work.eNone of the audio effects work when the unit is outputting bitstream signals from the DIGITAL 14
AUDIO OUT or HDMI AV OUT terminal.
eSome audio effects do not work or have less effect with some discs.-
e With HDMI AV OUT connections:
- Dolby Pro Logic II does not work.-
- Plays HDCD discs as normal CDs.-
- AUDIO ONLY does not work.-
No soundeAudio may not be heard when more than 4 devices are connected with HDMI cables. Reduce the -
number of connected devices.
eWhen AUDIO ONLY is on:
- Audio may not be output depending on the type of television.-
- Video and audio cannot be output from HDMI AV OUT terminal. Set this function to ?Off?.7
eThere may be a pause in sound when you change the play speed.8
Recording
Cannot record to digital eYou cannot record WMA/MP3.-
recording equipment.eYou cannot record DVDs that have protection preventing digital recording.-
(Incorrect sound recorded.)eYou cannot record DVDs if the recording equipment cannot handle signals with a sampling frequency of 48 kHz.-
eMake the following settings:
- Advanced Surround:Off13
- PCM Digital Output:Up to 48 kHz14
- Dolby Digital/DTS Digital Surround/MPEG: PCM14
Unit displays
?NOPLAY? eYou inserted a disc the unit cannot play; insert one it can.3
eYou inserted a blank disc.-
?U11?eThe disc may be dirty.16
?U15?eYou inserted a DVD-R that has not been finalized.3
?H ?eTrouble may have occurred. The number following ?H? depends on the status of the unit. Turn the unit off -
stands for a number.and then back to ON. Alternatively, turn the unit off, disconnect the AC mains lead, and then reconnect it.
eIf the service numbers fail to clear, note the service number and contact a qualified service person.-
?NODISC?eYou haven?t inserted a disc: Insert one.-
eYou haven?t inserted the disc correctly: Insert it correctly.6
?U70-1?eThe connected equipment is not HDMI compatible.-
?U70- ?eThe HDMI connection acts unusually.
stands for a number.- The connected equipment is not HDMI compatible.-
The actual number following ?U70-? - The HDMI cable is too long.-
will depend on the state of this unit.- The HDMI cable is damaged.-
Television displays
?/ ?eThe operation is prohibited by the unit or disc.-
Troubleshooting guide
?Cannot display group xx, content xx? eYou are trying to play incompatible groups or content.11
?Cannot play audio?eAudio has not been recorded, or recorded in a format this unit cannot playback. Video playback 3
?No audio?only is possible.
?Check the disc?eThis disc may be dirty.16
?Due to copyright protection, eShould you connect equipment that does not support CPPM (� page 16, Glossary), the audio from the 4
audio cannot be output from CPPM copy protected DVD-Audio cannot be output from HDMI AV OUT terminal. Connect the audio cable of
HDMI?the Audio/Video cable (L,R) to a HDMI compatible AUDIO IN terminal.
While ?HDMI Status? displayed, eIf you select an item without ?c ? in the ?Video Output Mode? in Picture Menu, it will not be 12
any items are not underlined.underlined.
?This disc may not be played in eYou can only play DVD-Video if their region number is the same or includes the same region number as Cover
your region?the unit or if the DVD-Video is marked ?ALL?. Confirm the region number for the unit on the rear panel.
No on-screen display.eSelect ?On? in ?On-Screen Messages? in ?Display? tab. 15
When setting ?Video Output eIf the connected equipment is compatible, selecting an item without an ?c ? will not distort the 12
Mode?, ?c? is not displayed next to picture.
a video output possible with the
connected equipment.
Maintenance
Clean this unit with a soft, dry cloth.
RQT7258
eNever use alcohol, paint thinner or benzine to clean this unit.e Before using chemically treated cloth, read the instructions that came
with the cloth carefully.
19 |
ACEC
