Operation Guide 3358/3368/3798
Setting the Analog TimeProgress Beeper
Perform the procedure below when the time indicated by the analog hands does notWhen the progress beeper is turned on, the watch uses beeps to signal countdown
match the time of the digital display.progress as described below.
" Starting from five minutes before the end of the countdown, the watch emits four
To adjust the analog timeshort beeps at the top of each countdown minute.
1.In the Timekeeping Mode, press C five times to enter" 30 seconds before the end of the countdown, the watch emits four short beeps.
the Hand Setting Mode." The watch emits a short beep for each of the last 10 seconds of the countdown.
2.Hold down A until the current digital time starts to" If the countdown start time is six minutes or greater, the watch emits a short beep for
flash, which indicates the analog setting screen.each second of the final 10 seconds before the five-minute point is reached. Four
3.Press D to advance the analog time setting byshort beeps are emitted to signal when the five-minute point is reached.
20 seconds.
" Holding down D advances the analog time setting atTo configure the countdown timer
high speed.1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
" If you need to advance the analog time setting a long way, hold down D until thecountdown start time starts to flash, which indicates the
time starts advancing at high speed, and then press B. This locks the high-setting screen.
speed hand movement, so you can release the two buttons. High-speed hand" If the countdown start time is not displayed, use the
movement continues until you press any button. It will also stop automaticallyprocedure under OTo use the countdown timer� to
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,display it.
or countdown beeper) starts to sound.2. Press C to move the flashing in the sequence shown
4. Press A to exit the setting screen.below to select other settings.
" The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.Start TimeAuto-repeat
" To return to the Timekeeping Mode, press C.
Progress Beeper
3.When the setting you want to change is flashing, use
World TimeB and D to change it as described below.
World Time digitally displays the current time in 27 cities
City code (29 time zones) around the world.SettingScreenButton Operation
" All of the operations in this section are performed in theStart TimeUse D (+) and B (�) to change the setting.
World Time Mode, which you enter by pressing C." You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
To view the time in another cityAuto-repeatPress D to toggle auto-repeat on ( displayed) and off
In the World Time Mode, press D to scroll eastwardly( displayed).
through city codes.Progress BeeperPress D to toggle the progress beeper on (ON) and off
" For full information about city codes, see the OCity Code(OF).
Table�.
Current time for " If the current time shown for a city is wrong, it probably4. Press A to exit the setting screen.
the selected city code means there is a problem with your Timekeeping Mode" You can also perform steps 1 and 2 of the above procedure whenever you need to
time and/or Home City code settings. Go to theview the current auto-repeat and progress beeper settings.
Timekeeping Mode and make the necessary
adjustments.To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
To toggle a city code time between Standard Time and Daylight Saving Time
" The countdown timer operation continues even if you
1. In the World Time Mode, use D to display the city code whose Standard Time/
Daylight Saving Time setting you want to change.exit the Countdown Timer Mode.
" Press D while a countdown operation is in progress to
2. Hold down A for about two seconds to toggle between Daylight Saving Time (DST
pause it. Press D again to resume the countdown.
indicator displayed) and Standard Time (DST indicator not displayed).
" The DST indicator is on the display whenever you display a city code for which" To completely stop a countdown operation, first pause it
(by pressing D), and then press A. This returns the
Daylight Saving Time is turned on.
countdown time to its starting value.
" Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
" Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.Stopwatch
DST indicator
The stopwatch lets you measure elapsed time, split times, and two finishes.
" The display range of the stopwatch is 59 minutes, 59.99 seconds.
" The stopwatch continues to run, restarting from zero after it reaches its limit, until
you stop it.
" The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
" Exiting the Stopwatch Mode while a split time is frozen on the display clears the split
time and returns to elapsed time measurement.
Module 3358Module 3368Module 3798" All of the operations in this section are performed in the Stopwatch Mode, which you
enter by pressing C.
Minutes 1/100 second
Split indicator
Countdown TimerSeconds
The countdown timer can be set within a range of one
Seconds minute to 60 minutes. An alarm sounds when theSplit
countdown reaches zero. The countdown timer also hasindicator
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
" All of the operations in this section are performed in theModule 3358Module 3368Module 3798
Countdown Timer Mode, which you enter by pressing
C.To measure times with the stopwatch
Elapsed Time
Configuring the Countdown Timer
Minutes
The following are the settings you should configure before
actually using the countdown timer.StartStopRe-startStopClear
Countdown start time; Auto-repeat on/off; Progress
beeper on/offSplit Time
" See OTo configure the countdown timer� for information
about setting up the timer.
StartSplitSplit releaseStopClear
Auto-repeat(Split indicator
When auto-repeat is turned on, the countdown automatically restarts from theTwo Finishes displayed)
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
SplitStopSplit releaseClear
When auto-repeat is turned off, the countdown stops when it reaches zero and theStart
display shows the original countdown start time.First runner finishes.Second runner finishes.Display time of second runner.
" Pressing D while an auto-repeat countdown is in progress pauses the currentDisplay time of
countdown. You can resume the auto-repeat countdown by pressing D, or you canfirst runner.
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
" When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
" When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
2 |
ACEC
CASIO
