GB
The cookers can be set for sypply both on the right or lefthand side.
In this case it is sufficient to reverse the position of the cad nipple
AB
INLETSTOP
TAB. D
Values referred to Hs - 15°C - 1013,25mbar
Cat. II 2H3+
ELECTRICAL CONNECTION
TABELLA GENERALE INIETTORI
This appliance must be installed by a qualified person inKind of gas mbar Nozzle Burners Power KW ConsumN°
accordance with the latest IEE Regulations and in compliancemanufacturer?s instructions.By pass
N° max. min. max. min.
115 Rapide 3,00 0,75 286 l/h 72 l/h reg.
Check that the voltage is the same as that stated on the rating plate.NATURAL 20 97 is located Semi rapideon the back cover. 1,75 0,48 167 l/h 46 l/h reg.
G 20 72 Auxiliary 1,00 0,33 95 l/h 31 l/h reg.
WARNING! THIS APPLIANCE MUST BE EARTHED 128 Triple crown 3,30 1,30 315 l/h 124 l/h reg.
If an fixed appliance is not equipped with supply cable and plug, theBUTANE 28-30 85 Rapide 3,00 0,75 219 g/h 55 g/h 42
We recommend that the cooker circuit is rated to 20 amps.G 30 65 Semi rapide 1,75 0,48 128 g/h 35 g/h 31
Cable type HO5 RRF 3 X 2.5 mm2 50 Auxiliary 1,00 0,33 73 g/h 24 g/h 27
PROPANE 37 93 Triple crown 3,30 1,30 241 g/h 95 g/h 60
Connecting the mains cable, and loosen the screws in the mains terminal block G 31, the cable lower thanfrom the floor. The cable
MINIMUM FLOW ADJUSTMENT FOR COOKTOP TAPS
To adjust the minimum, proceed as follows: switch the burner on, andsmall screwdriver in to the tap rod (fig. 11).adjustment screwtap rod (fig. 12).
Z
Fig. 11Fig. 12
Loosen the adjustment screw in order to increase the flow or tightenapproximatelyin length. adjustment screw must be fully screwed.when passing quickly from
Assemble the knob again.
IMPORTANT
The wires in the mains ........EARTHcable are coloured as follows:
BLUE ....................................NEUTRAL
BROWN ...............................LIVE
REPLACING OF THE CABLE
If the cable becomes damaged or worn, replace it, observing the
- open the box of the supply board as unscrew screw ?A? that secures the cable;shown in the diagram below;
APPLIANCE MAINTENANCE
- replace the cable with one of the same length and which corresponds
to the features described in the table; switch the appliance off, andWARNINGSthe gas tap;
- connect the ?green-yellow? earth wire to the terminal ? ?, leavingIsolate the cooker from the electricity supply before attempting todesigned to withstand highproceed as follows: remove the protectivet-out bulb with one of the same type.-fit the protective glass.
it approximately 10 mm longer than the live wire;
- connect the ?blue? neutral wire to the terminal marked ?N?;
- connect the live wire to the terminal marked ?L?.
E 14
GAS ADJUSTMENT25 W - 230 V~
T300°C
Always isolate the cooker from the electricity supply, shut off the gas
A
supply temporarily and proceed as follows.
- change the injectors,
- adjust the minimum flow of the burners.
DISMANTLING THE COOKTOP
If it becomes necessary to repair or replace internal components,as follows: remove the glass lid from its position by slidingthe burners and flame-spreaders (see fig. 13),located on the cooktop (see fig. 14). by unscrewing the 4 rear screws ?A? (see fig.
REPLACEMENT OF COOKTOP INJECTORS the cooktop injectors, proceed as follows: remove thereverse, ensuring you position the flame-spreader correctly.
15 ).
29 |
ACEC
ELECTROLUX
