Operating sequence
1. Check the filters The start of the countdown will occur after about 6
seconds from the last pressure of a programme push
Ensure they are clean and properly positioned (see button.
"Maintenance and cleaning").
The countdown will decrease with step of 3 hours and
you are informed of this by the indicator lights of the
2. Press the On/Off push buttonhours.
The On/Off indicator light will come on.During the countdown the only indicator lights
illuminated are the programme light and the light of the
number of hours to the start of the programme.
3. Check that there is rinse aid and salt
Once the delayed time has elapsed the programme will
The corresponding indicator lights will illuminate start if automatically.
refilling is necessary.It is possible to stop a countdown in progress or before it
starts, simply pressing the delay start push button until
4. Load the dishes the indicator lights of the hours are off.
Remove any scraps of food.
Pull the lower basket out and arrange the saucepans, 9. To cancel a programme in progress
plates and cutlery in it. A programme in progress can be cancelled at any time.
Pull the upper basket out and arrange the plates, Press for about 3 seconds the push button of the
saucers, glasses and cups etc. in it. running programme until all indicator lights are off.
Slide the baskets back into the machine. Only the On/Off indicator light will remain on once the
programme has been cancelled.
5. Ensure that the spray arms can It is now possible to select a new washing programme.
rotate freely.
10. At the end of the washing
6. Measure out detergent programme
The dishwasher will automatically stop and the phase
Add the required amount of detergent into the dispenser
according to the recommended quantity given in the indicator light end of programmewill come on.
The indicator light of the programme just ended will
Washing programmes chart. remain on.
Close the detergent dispenser lid.
The dishwasher has finished the programme only when
the phase indicator end lightof programmeis
7. Close the dishwasher doorilluminated.
If you do not wait for the end of the programme it will not
8a. Setting and starting the programme be possible to start a new programme if first you do not
cancel the previous. (For the formalities how to cancel a
without delay startprogramme see point 9).
Press the push button corresponding to the wanted If during the drying phase (drying indicator light
programme: the indicator light corresponding to the illuminated) the dishwasher door is opened or the On/Off
programme illuminates and the phase indicator lights push button is pressed, the running programme is
foreseen for that programme start flashing. automatically cancelled.
The start of the programme will occur after about 6 In this case the machine returns to setting mode and it is
seconds from the last pressure of a programme push possible to select a new washing programme without
button, in this time it is possible to change programme cancelling the previous.
simply pressing the push button of another programme.Switch off the dishwasher by pressing the On/Off push
Once the programme has started the phase indicator button and open the door.
lights will turn off except for the phase under wayW. ait a few minutes before removing the dishes; in
It is possible to interrupt the programme:this way they will be cooler.
opening the doorEmpty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
pressing the On/Off (in this case all the indicator lights dishes in the lower one.
turn off)
Close the door again o press the On/Off, the programme
will start from the point in which it was interrupted.Important!
In general it is not advisable to open the door while the
machine is working; if the door is opened however, a
8b. Setting and starting the programme safety device ensures that the machine stops.
with delay startCare must be taken if the door is opened during the hot
phase or immediately after a programme has finished, as
The setting of the delay start occurs before selecting the steam may escape.
programme.
Press the delay start push button and selected the
desired time (3, 6 or 9 hours) until the indicator light When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
corresponding to the chosen hours flashes.
Press the push button corresponding to the required water tap turned off.
programme: the indicator light corresponding to the
programme illuminates and the phase indicator lights for
that programme start flashing.
10 |
ACEC
