152976 53/2en per est 29-01-2002 17:04 Pagina 10
Operating sequence
that programme start flashing.
1. Check the filters
Ensure they are clean and properly positioned (see The start of the countdown will occur after about 6
"Maintenance and cleaning").seconds from the last pressure of a programme push
button.
2. Press the On/Off push buttonThe countdown will decrease with step of 3 hours and
you are informed of this by the indicator lights of the
The On/Off indicator light will come on.hours.
3. Check that there is rinse aid and salt During the countdown the only indicator lights
illuminated are the programme light and the light of the
The corresponding indicator lights will illuminate if number of hours to the start of the programme.
refilling is necessary.
Once the delayed time has elapsed the programme will
4. Load the dishes start automatically.
It is possible to stop a countdown in progress or before it
Remove any scraps of food.
Pull the lower basket out and arrange the saucepans, starts, simply pressing the delay start push button until
the indicator lights of the hours are off.
plates and cutlery in it.
Pull the upper basket out and arrange the plates, 9. To cancel a programme in progress
saucers, glasses and cups etc. in it.
A programme in progress can be cancelled at any time.
Slide the baskets back into the machine.Press for about 3 seconds the push button of the
5. Ensure that the spray arms can running programme until all indicator lights are off.
Only the On/Off indicator light will remain on once the
rotate freely.programme has been cancelled.
It is now possible to select a new washing programme.
6. Measure out detergent
Add the required amount of detergent into the dispenser 10. At the end of the washing
according to the recommended quantity given in the
programme
Washing programmes chart.
Important!The dishwasher will automatically stop and the phase
indicator light end of programmewill come on.
If the half load option is selected remember to The indicator light of the programme just ended will
reduce the quantity of detergent.
Close the detergent dispenser lid.remain on.
The dishwasher has finished the programme only when
the phase indicator end lightof programmeis
7. Close the dishwasher door
illuminated.
If you do not wait for the end of the programme it will not
8a. Setting and starting the programme be possible to start a new programme if first you do not
without delay startcancel the previous. (For the formalities how to cancel a
Press the push button corresponding to the wanted programme see point 9).
programme: the indicator light corresponding to the If during the drying phase (drying indicator light
illuminated) the dishwasher door is opened or the On/Off
programme illuminates and the phase indicator lights push button is pressed, the running programme is
foreseen for that programme start flashing.
Select, if required, the HALF LOAD option.automatically cancelled.
In this case the machine returns to setting mode and it is
The start of the programme will occur after about 6 possible to select a new washing programme without
seconds from the last pressure of a programme push cancelling the previous.
button, in this time it is possible to change programme
simply pressing the push button of another programme.Switch off the dishwasher by pressing the On/Off push
button and open the door.
Once the programme has started the phase indicator
lights will turn off except for the phase under way.Wait a few minutes before removing the dishes; in
this way they will be cooler.
It is possible to interrupt the programme:Empty the lower basket first and then the upper one; this
opening the doorwill avoid water dripping from the upper basket onto the
pressing the On/Off (in this case all the indicator dishes lights in the lower one.
turn off)
Close the door again o press the On/Off, the progImporramme tant!
will start from the point in which it was interrIn upted.general it is not advisable to open the door while the
machine is working; if the door is opened however, a
8b. Setting and starting the programme safety device ensures that the machine stops.
Care must be taken if the door is opened during the hot
with delay startphase or immediately after a programme has finished, as
The setting of the delay start occurs before selecting steam may the escape.
programme.
Press the delay start push button and selected the When the washing programme has finished, it is
desired time (3, 6 or 9 hours) until the indicator light
corresponding to the chosen hours flashes.recommended that the dishwasher is unplugged and the
water tap turned off.
Press the push button corresponding to the required
programme: the indicator light corresponding to the
programme illuminates and the phase indicator lights for
10 |
ACEC
