DISPLAY MEANING OF THE SYMBOLS: The functions activated by the push buttons are as follows:
LIGHTS: switch the lights on and off;
O MOTOR OFF: turn the motor off;
STAND_BY: The motor of the hood is off;
- reduces the motor speed;
+ increases the motor speed;
..... first, second , ?.speed;
TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th
speed, the led point connected with the selected speed, starts to flash for 10 minutes,
intensive speed activated; after which motor automatically stops.
MEANING OF THE LED POINTS: if the leds connected with the speeds are flashing, there is a
timing running.
1st Speed;
flashing led point: the timer is in action; 2nd Speed;
3rd Speed;
4th Speed;
(FLASHING F LETTER) grease-filters should be cleaned; 5th Speed; led point is flashing;
6th Speed; led point is flashing.
5th and 6th Speed must be used just for short periods as the hood is taking in a big quantity of air
only in case of filtering hood (flashing C letter) carbon filters should be so after 10 minutes the motor is automatically reset to the 3rd speed.
replaced. 7.2.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTER
7.1.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTERS the electronic controls with led points allow automatic control of the grease filters and carbon
The electronic controls with display allow automatic control of the grease filters and the carbon filters (only in case the hood is used in filtering version) so that the user does not have to
filters (only when the hood is used in the filtering version), so that the user does not have to remember when maintenance was last carried out.
remember when maintenance was last carried out. When the grease filters require cleaning, an
When the metallic grease filters have to be cleaned, the letter F on the display will flash. acoustic signal is issued for some seconds
When the carbon filters have to be replaced, the letter C on the display will flash. and the led point above the timer push
It is possible to consult the electronic system concerning how clean the grease filters are and how button keeps on flashing.
worn the carbon filters are, as follows: stop the motor and ... When the carbon filters need replacing, an
acoustic signal is issued for some seconds
? to find out how clean the fat filters are, press the O and - buttons at the same time. On the and the led point above the light push
display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is;
button keeps on flashing.
? to find out how worn the carbon filters are, press the buttons O and +. On the display, a 7.2.3. TO PUT THE GREASE AND CARBON FILTERS CONTROL BACK TO ZERO
number between 0 and 9 will appear, the smaller the number, the more worn the filter is. To put the grease filter counter back to zero you must:
7.1.3 TO PUT THE GREASE AND/OR CARBON FILTER CONTROL BACK TO ZERO: " stop the motor;
" stop the motor (stop position); " press the timer push button twice in succession, until you hear the acoustic signal.
" push the push-buttons 0 (zero) and T (timer) at the same time for a few seconds. This symbol To confirm reset the led point stops flashing.
appears and a ?bip? is issued. To put the carbon filter counter back to zero you must:
7.1.4 SETTING THE SUCTION /FILTERING USE OF THE HOOD " stop the motor;
The hood is delivered standard for suction use (only with flashing F letter). If you wish to use it in " press the light push button twice in succession until you hear the acoustic signal.
the filtering version (F and C flashing) proceed as follows: To confirm reset, the led point stops flashing.
press the buttons and T on the display for about 5 seconds, the following symbol will ATTENTION: The light push button does not switch on/off the lights until you hear acoustic
appear followed by a 0. signal.
7.2.4 SETTING OF THE SUCTION/FILTERING USE OF THE HOOD
" At each pressure of the Light Button, it is possible to change the value shown from the O
(suction function), to 1 (filtering function) and viceversa. The hood is delivered standard for suction use.
If you wish to use the hood in the filtering version, proceed as follows:
" Press the O button (zero) to confirm the choice effected in the previous point.
7.2.1 SOFT TOUCH CONTROLS WITH PUSH BUTTONS SCREENPRINTED ON S/STEEL " disconnect hood from electricity and then reconnect this to electricity;
" the led-point of the light push button will flash for approx. 10 seconds. During this time press
(FIG.11b)
the light push button 3 times. Three acoustic signals are issued to point out the new setting.
WARNING ! To activate the functions connected to these push buttons, it is necessary to ATTENTION: during the suction/filtering setting phase no function can be activated.
apply a little pressure just lightly and for a short time. If pressure is too lengthy on the
If the hood is set for suction, when connected the led point over the LIGHT Push Button is
push buttons the connected functions are not activated. flashing. If the hood is set for filtering, when connected the led point over the
TIMER Push Button is flashing. |
ACEC
ELECTROLUX
